Smontaggio Del Mantello - Ecoflam LINDA 23 BOX CPR Instrucciones De Uso Para El Usuario

Tabla de contenido

Publicidad

SVUOTAMENTO DELL'IMPIANTO DI
RISCALDAMENTO
Lo svuotamento dell'impianto di riscaldamento deve
essere eseguito nel seguente modo:
- spegnere la caldaia;
- ruotare il rubinetto di scarico dell'impianto racco-
gliendo in un contenitore l'acqua che fuoriesce.
- svuotare dai punti più bassi dell'impianto (dove pre-
visti). Se si prevede di tenere l'impianto fermo, nelle
zone in cui la temperatura ambiente può scendere nel
periodo invernale al di sotto di 0°C, si consiglia di
aggiungere liquido antigelo a base di glicoli etilenici
all'acqua dell'impianto di riscaldamento in alternativa
a ripetuti svuotamenti.
SVUOTAMENTO DELL'IMPIANTO
SANITARIO
Ogni qualvolta esista pericolo di gelo, deve essere
svuotato l'impianto sanitario nel seguente modo:
- chiudere il rubinetto generale della rete idrica;
- aprire tutti i rubinetti dell'acqua calda e fredda;
- svuotare dai punti più bassi (dove previsti).

SMONTAGGIO DEL MANTELLO

Per poter eseguire le operazioni in seguito descritte, è
necessario smontare il "mantello" della caldaia operando
nel seguente modo:
- Svitare le quattro viti poste nella parte superiore della
caldaia;
- Svitare le quattro viti poste nella parte inferiore della
caldaia;
- Sollevare il"mantello" verso l'alto e sganciarlo dalla
caldaia.
- Svitare le due viti poste nella parte anteriore del
pannello porta-strumenti ed accompagnarlo nella
sua rotazione.
I
111
VACIADO DE LA INSTALACION DE
CALEFACCION
El vaciado de la instalación de calefacción debe de
ser ejecutado en el siguiente modo:
- Apagar la caldera;
- Girar el válvula de desagüe de la instalación reco-
lectando en un contenedor el agua que se derrame.
- Favorecer el vaciado utilizando lo puntos inferiores
de la instalación (si los posee). Si se prevee de tener
la instalación inactiva, en zonas en las que la tempe-
ratura ambiente puede descender durante el invierno
por debajo del 0°C, se recomienda de añadir líquido
anticongelante a base de etilenglicol al agua de la
instalación de calefacción en alternativa a repetidas
operaciones de vaciado.
VACIADO DE LA INSTALACION PAR-
TE USO HIGIENE
Cada vez que exista el peligro de heladas, debe de ser vaciada la
instalación uso higiene de la siguiente manera:
- Cerrar la válvula general de la red hidráulica;
- Abrir todas las llaves del agua fría y caliente;
- Favorecer el vaciado utilizando lo puntos
inferiores de la instalación (si los posee).
DESMONTAJE DE LA CAPA
Para poder ejecutar las operaciones descritas a conti-
nuación es necesario desmontar la capa de la caldera
actuando en el siguiente modo:
- Desatornillar los cuatro tornillos ubicados en la parte
inferior de la caldera.
- Alzar la capa hacia arriba y separarla descolgándola
de la caldera.
- Desatornillar lo dos tornillos en la parte anterior del
panel instrumental y acompañarlo en su rotación.
E
EPTYING THE HEATING SYSTEM
The heating system must be emptied as follows:
- Turn off the boiler;
- Open the drain valve for the system and place a
container below to catch the water that comes out;
- Empty the system at the lowest points (where pre-
sent). If you plan on not using the heating system for
an extended period of time, it is recommended that
you add antifreeze with an ethylene glycol base to the
water in the heating lines and radiators if the ambient
temperature drops below 0°C during the winter. This
makes draining the entire system unnecessary.
DRAINING THE DOMESTIC HOT
WATER SYSTEM
Whenever there is the danger of the temperature drop-
ping below the freezing point, the domestic hot water
system must be drained as follows:
- Turn off the general water valve for the household
plumbing system;
- Turn on all the hot and hold water faucets;
- Empy the remaining water from the lowest points in
the system (where present).
REMOVING THE OUTER SHELL
In order to perform the procedures described below, the
outer shell of the boiler must be removed as follows:
- Remove the four screws located at the bottom of the
boiler;
- Lift the shell upwards and unhook it from the boi-
ler.
- Remove the two screws located at the front part of
the control panel and turn it.
GB
LINDA
-21-

Publicidad

Tabla de contenido
loading

Tabla de contenido