Residual Risk; Ec Declaration Of Conformity; Mains Connection - Milwaukee MS 216 SB Manual Original

Keep the oor area free of loose material e.g. chips and cut-o s.
Refrain from removing any cut-o s or other parts of the workpiece
from the cutting area whilst the machine is running and the saw
head is not in the rest position.
Never reach into the danger area of the machine when it is running.
Always use the protective shields on the machine.
Any faults with the machine, including any related to the safeguard
or the saw blades, must be reported to the persons in charge of safety
as soon as the faults are discovered.
Do not clamp the protective swing guard.
Long workpieces must be adequately supported.
The handle lock must always be engaged when transporting the
mitre saw.
Do not replace the LED with a di erent type. Any repairs must only be
carried out by the authorized service agent.
LASER
Do not stare into beam. Do not point laser light at other persons.
Do not view directly into beam with optical instruments (binocular,
telescope).
GB
Do not point laser at re ective surfaces.
Avoid exposure to laser radiation. Laser may emit hazardous radiation.
Do not replace the installed laser with a di erent type.
Any repairs must only be carried out by the authorized service agent.
SPECIFIED CONDITIONS OF USE
The mitre saw can be used for sawing solid wood, bonded wood,
glued veneer, materials similar to wood, and plastics.
Stock having a round or irregular cross section (such as rewood) must
not be cut, as it can not be securely held during cutting. When sawing
thin stock layed on edge, a suitable auxilary fence must be used for
rm support.

RESIDUAL RISK

Even when the product is used as prescribed, it is still impossible to
completely eliminate certain residual risk factors. The following ha-
zards may arise in use and the operator should pay special attention
to avoid the following:
• Impairment of hearing, restrict exposure and wear appropriate
hearing protection.
• Measures that can be taken by operator to possibly reduce the
e ects of vibration and limit the amount of exposure.
• Health hazards caused by breathing dust developed when sawing
wood, wear a mask if necessary.

MAINS CONNECTION

Connect only to single-phase AC system voltage as indicated on the rating
plate. It is also possible to connect to sockets without an earthing contact as
the design conforms to safety class II.
Appliances used at many di erent locations including open air should be
connected via a residual current device (FI, RCD, PRCD) of 30mA or less.
Only plug-in when machine is switched o .
Keep mains lead clear from working range of the machine. Always lead the
cable away behind you.
Before use check machine, cable, and plug for any damages or material
fatigue. Repairs should only be carried out by authorised Service Agents.
English
22
MAINTENANCE
If the supply cord of this power tool is damaged, it must be
replaced by a specially prepared cord available through the service
organization.
Be sure to disconnect the tool from the power supply before atta-
ching or removing the saw blade.
Replace the table insert when worn
Clean the tool and guarding system with clean cloths.
The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described,
please contact one of our Milwaukee service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state
the machine type printed as well as the six-digit No. on the label
and order the drawing at your local service agents or directly at:
Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Winnenden,
Germany.

EC DECLARATION OF CONFORMITY

We declare under our sole responsibility that the product described
under "Technical Data" ful lls all the relevant provisions of the directi-
ves 2011/65/EU (RoHS), 2004/108/EC, 2006/42/EC and the following
harmonized standards have been used:
EN 61029-1:2009 + A11:2010
EN 61029-2-9: 2012+A11:2013
EN 55014-1:2006+A1:2009+A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-3:2013
EN 50581:2012
Winnenden, 2014-10-06
Alexander Krug / Managing Director
Authorized to compile the technical le
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany