Black+Decker KA280 Traducción De Las Instrucciones Originales página 8

ENGLISH
When the front part of the tip is worn, detach it from the
u
sheet, reverse it and press it onto the sanding base
again.
When the whole tip is worn, remove it from the sanding
u
base and fit a new diamond shaped tip (13).
Tip of the sanding base (fig. G)
When the sanding base tip (7) is worn, it can be reversed
or replaced. When the diamond shaped tip holder (16) is
worn, it can be replaced. Spare parts are available from your
BLACK+DECKER dealer.
Remove the screw (17).
u
Reverse or replace the worn part.
u
Fit and tighten the screw (17).
u
Finger attachment (fig. H)
The finger attachment is used for fine detail sanding.
Remove the screw (17).
u
Remove the diamond-shaped tip holder (16) from the
u
sanding base.
Fit the finger attachment (8) onto the sanding base (6).
u
Fit and tighten the screw (17).
u
Fit the appropriate sanding sheet (18) onto the finger
u
attachment.
Profile attachment
The profile attachment is used for contour sanding.
Fitting the profile attachment (fig. I)
Remove the screw (17).
u
Remove the diamond-shaped tip holder (16) from the
u
sanding base.
Fit the profile attachment (19) onto the sanding base.
u
Fit and tighten the screw (17).
u
Fitting and removing a sanding profile (fig. J & K)
Choose the sanding profile most suitable for your
u
application.
Place one end of the sanding profile (20) into the recess
u
at the front end of the profile attachment (19).
Push the other end of the sanding profile until it clicks
u
into place.
To remove the sanding profile (20), push it forward and
u
pull the rear end out of the profile attachment (19).
Fitting a sanding sheet onto a sanding profile (fig.
L)
Align the sanding sheet (21) with the sanding
u
profile (20).
Press the sanding sheet onto the sanding profile,
u
making sure that the sanding sheet follows the shape
of the profile.
8
(Original instructions)
Louvre attachment (fig. M) (KA280L only)
With the louvre attachment you can work in crevices.
Remove the screw (17).
u
Remove the diamond-shaped tip holder (16) from the
u
sanding base.
Fit the louvre attachment (22) onto the sanding base.
u
Fit and tighten the screw.
u
Fit the appropriate sanding sheet onto the louvre
u
attachment.
The additional piece of hook and loop fastener (23) can be
attached to the top surface of the louvre attachment to allow
for sanding using both sides.
Remove the backing paper from the hook and loop
u
fastener (23).
Stick the hook and loop fastener to the top surface of the
u
louvre attachment (22).
Fit the sanding piece to the hook and loop fastener.
u
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Do not cover the ventilation slots when using the
tool. Hold the tool as shown in fig. R. Make sure that the
sanding base is flat on the workpiece.
Store the tool with a base in place.
u
Keep hands away from the spindle area on the tool.
u
Do not turn the Autoselect® dial while the unit is running.
u
Do not rest fingers on the base during use.
u
Switching on and off (fig. N)
To switch the tool on, depress the on/off switch (1) to posi-
u
tion I.
To switch the tool off, depress the on/off switch (1) to posi-
u
tion O.
Autoselect® Technology (fig.O)
This sander is fitted with an Autoselect® dial (2) which shows
various sanding applications. They are used to select the
correct operating mode for your particular sanding operation.
Using the Autoselect® dial (2), choose from one of the
u
following applications:
- Detail sanding (A).
- Corner sanding (B).
- Flush sanding (C).
- Random orbit sanding (D).
The correct base to be used and the recommended sanding
speed will be displayed in the base/speed setting
window (3).
Note: You can override the selected speed at any time by
moving the Autoselect® dial to positions (A) and (B), slower
speeds, or positions (C) and (D), higher speeds.