Technical Characteristics; Connection Of Other Devices - Nice ROAD400 Manual De Instrucciones

OPERATING LIMITS:
in general, ROAD400 is suitable for the automation of gates featuring leaves up to 8 m wide and weighing up to 400 kg, as shown in Tables 1
and 2. The length of the leaf makes it possible to determine both the maximum number of cycles per hour and consecutive cycles, while the weight makes it possible to
determine the reduction percentage of the cycles and the maximum speed allowed.
TABLE 1 - Limits in relation to the length of the leaf
Leave width m Max cycle/hour
Up to 5 20
5 - 7 16
7 - 8 14

TECHNICAL CHARACTERISTICS:

notice. In any case, the manufacturer guarantees their functionality and fitness for the intended purposes. All the technical characteristics refer to a room temperature of
20°C (± 5°C).
Type
Pinion
Peak thrust
Nominal torque
Idling speed
Nominal torque speed
Maximum frequency of operating cycles
Maximum continuous operating
ROAD400 Power supply
ROAD400/V1 Power supply
Max. absorbed power
Insulation class
Flashing light output
STOP input
STEP BY STEP input
Radio AERIAL Input
Radio receiver
Programmable functions
Recognition functions
Operating temperature
Use in acid, saline or potentially explosive
atmosphere
Protection class
Dimensions and weight
ACCESSORIES:
ROAD400 is also available with the PS124 - 1.2 Ah back-up battery with incorporated charger, as an optional accessory. To connect the back-up
battery, see Figure 1.
Fig.1

CONNECTION OF OTHER DEVICES:

If the user needs to feed external devices such as a proximity reader for transponder
cards or the illumination light of the key-operated selector switch, it is possible to tap
power as shown in Figure 2. The power supply voltage is 24Vcc -30% - +50% with
a maximum available current of 100mA.
ENGLISH
Max. no. of consecutive cycles
15
12
9
Nice S.p.a., in order to improve its products, reserves the right to modify their technical characteristics at any time without prior
Electromechanical gearmotor for the automatic movement of residential sliding gates including electronic control unit
Z: 15; Module: 4; Pitch: 12.5 mm; Pitch diameter: 60 mm
12 Nm; corresponds to the ability to start a leaf with a static friction of max. 400 N moving
5 Nm; corresponds to the ability to keep a leaf with a dynamic friction of max. 167 N moving
0.25 m/s; the control unit allows 2 speeds to be programmed, equal to: 0.13 m/s or 0.25 m/s
0,16 m/s
50 cycles per day (the control unit allows up to the maximum described in tables 1 and 2)
time 9 minutes (the control unit limits the continuous operation up to the maximum described in tables 1 and 2)
230 Vac (+10% -15%) 50/60 Hz
120 Vac (+10% -15%) 50/60 Hz
210 W (1,1 A)
1 (a safety grounding system is required)
For 1 LUCYB flashing light (12 V, 21 W lamp)
For normally open contacts, for 8.2 KΩ constant resistance, or normally closed contacts; with self-recognition (any variation from
the memorized status causes the 'STOP' command)
For normally open contacts (the closing of the contact causes the "STEP-BY- STEP" command)
52 Ω for RG58 or similar type of cable
Incorporated
2 ON-OFF functions and 3 adjustable functions (see tables 12 and 14 of instruction manual ROAD200)
Open or Normally Closed contact or 8.2 KΩ resistance) - Recognition of the length of the gate and calculation of the slowdown
and partial opening points
-20°C ÷ 50°C
No
IP 44
330 x 195 h 277 mm; 8 kg
TABLE 2 - Limits in relation to the weight of the leaf
Leaf weight kg
Up to 200
200÷300
300÷400
Fig.2
% cycles
100%
85%
70%