Technical Characteristics - Nice RUN1800 Instrucciones Y Advertencias Para La Instalación Y El Uso

8) Technical characteristics

With the aim of improving products, Nice S.p.a reserves the right to modify technical characteristics at any time without notice, while main-
taining the same functionalities and intended use.
All technical characteristics stated refer to an ambient temperature of 20°C (±5°C).
RUN Technical characteristics
Model type
Type
Pinion
Maximum torque on start-up
[corresponds to ability of generating the
force required to move the leaf]
Nominal torque
[corresponds to the ability of generating the
force to maintain the leaf in movement]
Speed (no-load)
Speed (at nominal torque)
Maximum frequency of operating cycles (at
nominal torque)
Maximum time of continuous operation (at
nominal torque)
Operating limits
Durability
Power supply RUN 1800 - 2500
Power supply RUN 1800/V1-2500/V1
Maximum power absorption on start-up
[corresponding to Amps]
Power at nominal torque
[corresponding to Amps]
Insulation class
Flashing light output
Gate open indicator output
BLUEBUS output
STOP input
Step-by-step input
OPEN input
CLOSE input
Radio connector
Radio ANTENNA input
Programmable functions
Functions in self-learning mode
Operating temperature
Use in particularly acidic, saline or potentially
explosive atmospheres
Protection rating
Dimensions and weight
* Optional 12-tooth 6 module pinion available
** At 50°C and with a gate of 15 metres, the maximum operating frequency is 7 cycles/hour (equal to a cycle of 40%).
*** At 50°C the maximum continuous operation time is 10 minutes.
24
RUN 1800 - RUN 1800P - RUN 1800/V1
Electromechanical gearmotor for automatic movement of sliding gates for industrial use
complete with electronic control unit.
Number of teeth 18; Module 4 *
40Nm
(1110N)
20Nm
(560N)
10m/min (12m/min version /V1)
8,5m/min (8.9m/min version /V1)
11 cycles/hour (264 cycles/day),
for a gate of 15m (equal to a cycle of 63%),
(the control unit limits cycles to the max-
imum number specified in tables 2 and 3)**
40 minutes (the control unit limits
continuous operation to the maximum
limits as specified in tables 2 and 3)***
In general RUN is designed for the automation of gates with the weights and lengths as
specified in tables 2, 3 and 4
Estimated between 150.000 cycles and 450.000 cycles according to conditions specified
in table 4
230Vac (+10% -15%) 50 Hz
120Vac (+10% -15%) 60 Hz
700 W [3 A] [5 A version /V1]
400 W [1.8 A] [3 A version /V1]
1 (safety earthing required)
For 2 Flashing lights LUCYB (lamp 12V, 21W)
For 1 24V lamp of maximum 4W (output voltage may vary between -30 and +50% and
can also control small relays)
One output with maximum load of 15 BlueBus units
For normally closed contacts , normally open contacts or with constant 8,2kΩ. resistance; in self-
learning (a variation with respect to memorised value generates the STOP command)
For normally open contacts (contact closure generates S.S. command)
For normally open contacts (contact closure generates OPEN command)
For normally open contacts (contact closure generates CLOSE command)
SM connector for receivers SMXI; SMXIS or ONEXI
Input ANTENNA Radio 52Ω for cable type RG58 or similar
8 ON-OFF type functions and 8 settable functions (see tables 7 and 9)
Self-learning of devices connected to BlueBus output.
Self-learning of "STOP" device type (contact NO, NC or 8,2kΩ resistance) Self-learning of
gate length and calculation of deceleration and partial opening points.
-20°C ÷ 50°C
No
IP 44
400 x 255 h 390; 24.5 kg
RUN 2500 - RUN 2500P
50Nm
(1390N)
30Nm
(830N)
15 cycles/hour (365 cycles/day),
for a gate of 15m (equal to a cycle of 63%),
(the control unit limits cycles to the max-
imum number specified in tables 2 and 3)**
60 minutes (the control unit limits
continuous operation to the maximum
limits as specified in tables 2 and 3)***
870 W [3.8 A]
600 W [2.7 A]