Auto Calibration - Uline H-1114 Manual Del Usuario

WEIGHT TOTALIZING CONTINUED
3. When scale stabilizes UNIT WEIGHT displays the total
number of additions.
WEIGHT
SMPL
→ 0←
WT
PC
NET NET
WT
4. After 3 seconds, scale returns to weighing mode.
WEIGHT
SMPL
→ 0←
WT
PC
NET NET
WT
CLEAR ALL TOTALIZED VALUES
Press TOTAL CE to clear all of the totalized values. " " next
to M+ icon on QUANTITY display switches off. Totals for
weight, number of additions and quantity reset to zero.
NOTE: All totals will be lost if the scale is
switched off.
CALIBRATION

AUTO CALIBRATION

You must use calibration weights to accurately calibrate
the scale. Calibration weights totaling at least 10% of
scale's capacity must be used for accurate calibration.
1. With the scale displaying "0", press and hold •, then
press UNIT WT PRESET until the WEIGHT display flashes
the scale capacity. Release the keys.
WEIGHT
SMPL
→ 0← 3
WT
PC
NET NET
WT
2. Place weights on the scale equal to the full load
capacity. When scale stabilizes, it calibrates
automatically.
3. While the scale counts down to 0, remove the
weights from the scale. The calibration is complete.
4. Press CE to exit from the calibration mode.
NOTE: If weights equalling the full load are not
available, you can enter a weight that is less
than the full load.
5. With the scale displaying "0", press and hold •, then
press UNIT WT PRESET until the WEIGHT display flashes
the scale capacity. Release the keys.
6. Enter the weight to be used, then place the weight
on the scale. When the scale stabilizes, it calibrates
automatically.
PAGE 7 OF 18
USING THE SCALE CONTINUED
UNIT WEIGHT QUANTITY
3
M+
3
STABLE
UNIT WEIGHT QUANTITY
3
M+
3
STABLE
UNIT WEIGHT QUANTITY
M+
3
STABLE
7. While the scale counts down to 0, remove the
weights from the scale. The calibration is complete.
8. Press CE to exit from the calibration mode.
RECALL THE ORIGINAL CALIBRATION VALUES
1. Press and hold CE, then press UNIT WT PRESET until
Pcs
the scale counts down to 0. Release the keys. The
scale will revert to the original factory calibration
values.
UNIT WEIGHT PRESET MEMORY
The scale can store 10 sets of unit weight presets in the
Pcs
number keys (0 - 9). Once saved, pressing a particular
number key will display the unit weight saved in that
memory.
NOTE: The UNIT WT PRESET key is a dual function
key. Determine if Unit Wt Preset is set as the
main function or the secondary function of
this key. If unit weight preset is the secondary
function, you'll have to hold the UNIT WT PRESET
key down for 3 seconds to activate the feature.
SETTING A UNIT WEIGHT PRESET
1. Use the number keys (0-9) to enter the unit weight
value you wish to save.
WEIGHT
→ 0← 3
NET NET
2. Press UNIT WT PRESET.
WEIGHT
→ 0← 3
Pcs NET NET
3. Press UNIT WT PRESET again.
WEIGHT
→ 0← 3
NET NET
4. Press any number key (0-9) to save the weight in that
key's memory.
WEIGHT
→ 0← 3
NET NET
UNIT WEIGHT
SMPL
M+
WT
PC
3
STABLE
WT
UNIT WEIGHT
SMPL
M+
WT
PC
3
STABLE
WT
UNIT WEIGHT
SMPL
M+
WT
PC
3
STABLE
WT
UNIT WEIGHT
SMPL
M+
WT
PC
3
STABLE
WT
QUANTITY
Pcs
QUANTITY
Pcs
QUANTITY
Pcs
QUANTITY
Pcs
0613 IH-1114