Introduction; General Warnings; Certification; Technical And Constructional Characteristics, Dimensions - Ferroli PREXTHERM RSW 1250N Instrucciones Para El Uso, La Instalación Y El Montaje

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 1
PREXTHERM RSW N
1.

INTRODUCTION

Dear customer:
Thank you for choosing a PREXTHERM RSW N boiler. This manual was written to provide information, warnings and advice on the proper
installation, use and maintenance of the boiler.
Please read it carefully and save it for future reference. It is in your own interest to carefully follow and observe the instructions given in this
manual, in order to fully enjoy this high-quality product.
Failure to comply with and observe the instructions contained in this manual exonerates the manufacturer from all liability, and invalidates the warranty.
2.

GENERAL WARNINGS

- The instructions manual is an integral part of the product, and provides a description of all instructions that must be observed during the
installation, use and maintenance phase.
- This appliance must only be used for the purpose for which it was expressly intended.
- This appliance is intended to heat water to below-boiling temperatures at atmospheric pressure, and must be connected to a cen-
tral heating and/or domestic hot water distribution system, in accordance with its characteristics, performance, and heat output.
- Before installation, check that the boiler has not been damaged during handling and transport.
- The boiler is to be installed on a non-combustible base.
- The boiler is to be installed with a distance of at least 100 mm to any combustible material or component.
- The installation must be performed by duly qualified personnel, in accordance with current standards.
- Before performing any cleaning or maintenance operations, unplug the appliance from the mains power supply.
- THE MANUFACTURER is not liable for any damage to people or things due to errors in installation, adjustment, maintenance, or improper use.
- The boiler and corresponding system must be commissioned by authorized personnel.
- Commissioning is performed in order to verify proper operation of all adjustment and control devices.
- Qualified personnel must be contacted if the appliance is not used for an extended period.
Standards
The installer must observe current local regulations with regard to: the site chosen for the installation of the boiler, compliance with required ventila-
tion conditions, the tightness of the connection to the chimney, connections to fuel lines, electrical systems, and any other relevant safety standards.
Warranty conditions
The warranty is only valid if the standards and recommendations for use contained in this manual are observed. Any non-compliance or modifi-cation will void
the warranty. The warranty does not cover damage caused by acidic condensate corrosion from the products of combustion, or the formation of deposits caused
by the use of hard or aggressive water, as these are caused solely by system operation.
3.

CERTIFICATION

The CE marking certifies that the products meet the essential requirements of the GAR regulation and other applicable directives.
The declaration of conformity may be requested from the manufacturer.
PRODUCT IDENTIFICATION CODES
PREXTHERM RSW 1250N
PREXTHERM RSW 1480N
PREXTHERM RSW 1600N
PREXTHERM RSW 1890N
COUNTRIES OF DESTINATION: ES - IT - FR - RU
4.

TECHNICAL AND CONSTRUCTIONAL CHARACTERISTICS, DIMENSIONS

4.1 Description of the appliance

The construction of the boilers in the PREXTHERM RSW N series guarantees high power and efficiency with low flue gas temperatures, thus
ensuring low polluting emissions. They are manufactured in accordance with standard EN 303, part 1. The main technical elements of the
design are:
- careful design of geometries to achieve an optimum ratio between combustion volumes and heat exchange surfaces.
- the choice of materials used, to ensure long boiler life.
The boilers feature pressurized combustion with 2 flue passes, a horizontal-cylinder configuration, and flame reversal in the furnace, completely
surrounded by the water that cools it. The flame produced by the burner is reversed peripherally toward the front, where the flue gas enters the
tube bundle, featuring turbulators to create a swirling path that increases the heat exchange by convection. On leaving the tube bundle, the flue
gas enters the rear chamber and is transferred to the chimney.
The boilers are fitted with a door featuring hinges that can be reversed for opening to the right or left, and is adjustable in both height and dep-
th. The body is insulated with a thick layer of glass wool, and covered with a further layer of tearproof material. The external finish consists of
painted steel panels.
0QCJ00XA
PREXTHERM RSW 2360N
0QCL00XA
PREXTHERM RSW 3000N
0QCN00XA
PREXTHERM RSW 3600N
0QCP00XA
PREXTHERM RSW 4000N
cod. 3545453/0 - 06/2019
0QCS00XA
PREXTHERM RSW 4500N
0QCU00XA
PREXTHERM RSW 5000N
0QCV00XA
PREXTHERM RSW 6000N
0QCW00XA
0QCX00XA
0QCY00XA
0QCZ00XA
29
EN

Publicidad

Tabla de contenido
loading

Tabla de contenido