Mechanical Installation - Oase Lunaled Creative Set Instrucciones De Uso

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 21
- GB -
Pos: 96 /Alle Produkte/Überschriften/H2 Sicherer Betrieb @ 7\mod_1204022429287_121.doc @ 44671 @
Safe operation
Pos: 97 /Alle Produkte/Sicherheit/Sicherer Betrieb/SIC ERW Sich. Betrieb - Nicht in Lichtquelle schauen @ 11\mod_1251731754794_121.doc @ 72106 @
− Never look directly into the light source of the unit.
Pos: 98 /Alle Produkte/Sicherheit/Sicherer Betrieb/SIC ERW Sich. Betrieb - Steckdose/Netzstecker trocken @ 11\mod_1252350585923_121.doc @ 73043 @
− Keep the socket and power plug dry.
Pos: 99 /Alle Produkte/Sicherheit/Sicherer Betrieb/SIC ERW Sich. Betrieb - Nur mit Trafo aus Liefer @ 11\mod_1250506467398_121.doc @ 69370 @
− Only operate the unit with the supplied transformer.
Pos: 100 /Alle Produkte/Sicherheit/Sicherer Betrieb/SIC ERW Sich. Betrieb - Bei beschädigten Ltg. entsorgen @ 11\mod_1252351233965_121.doc @ 73070 @
− The power connection cables cannot be replaced. When the cable is damaged, the unit or the component needs to
be disposed of.
Pos: 101 /Alle Produkte/Sicherheit/Sicherer Betrieb/SIC BAS Sich. Betrieb @ 11\mod_1250507406044_121.doc @ 69397 @
− Never operate the unit if either the electrical cables or the housing are defective!
− Do not carry or pull the unit by its electrical cable.
− Route all cables such that damage is excluded and nobody can trip over them.
− Never open the unit housing or its attendant components, unless this is explicitly required in the operating
instructions.
− Only use original spare parts and accessories for the unit.
− Never carry out technical modifications to the unit.
− Only have repairs carried out by customer service points authorised by OASE.
Pos: 102 /Alle Produkte/Dummy_module/Abstand 6 pt @ 7\mod_1196627997106_0.doc @ 41651 @
Pos: 103 /Alle Produkte/Überschriften/H1 Mechanische Installation @ 10\mod_1249492027148_121.doc @ 67959 @

Mechanical installation

Pos: 104 /Lampen/Wasserspieltechnik/Lunaled Creative/INS 1 Lunaled installieren, Deckel anpassen @ 11\mod_1250508105783_121.doc @ 69451 @
Installation idea (C)
The unit set includes a 6 ltr. water container and a plastic cover with sponge and splash guard. The cover can be cut
into any desired shape using household scissors. The plastic cover is used to fasten the pump and to hold the decora-
tive materials, such as as pebbles, which you will later use to surround the Lunaled water feature. When the material is
evenly distributed, the plastic cover can hold a maximum of 2 kg, otherwise you must provide additional support.
Cutting the cover (D, E)
− Select a decorative vessel of any desired shaped (9) in which you can place the water container (3) included in the
set. As an alternative, you can use your own water container, provided that the pump cannot run dry. Use wooden
blocks (10) or the like for height compensation.
− Cut the cover such, that it rests securely on the water container and can be lowered together into the decorative
vessel. The lines on the underside of the cover serve as a cutting aid. Prevent risk of injuries: Deburr sharp edges
and round-off pointed corners which can occur when the cover is cut to shape! Handle the cover carefully!
Supplied water container: Fastening the Lunaled (F , G)
− Unscrew the stainless steel cap (11) from the Lunaled (5).
− Insert the Lunaled (G, 5) into the centre opening of the cover from below.
− Refit the stainless steel cap and hand tighten.
− Place the extension tube (4) on the pump (6) and tighten.
− Insert the extension tube into the rubber adapter. Ensure that the Lunaled cable is routed correctly in the cable duct
(12).
− Insert the sponge into the cover.
Self-provided water container: Fastening the Lunaled (F , H)
− Unscrew the stainless steel cap (F, 11) from the Lunaled (5).
− Insert the Lunaled (H, 5) into the centre opening of the cover from below.
− Refit the stainless steel cap and hand tighten.
− Insert the intake socket of the pump (6) into the rubber adapter. Ensure that the Lunaled cable is routed correctly in
the cable duct (12).
− For instance, use a cable binder (13, not included in the delivery scope) to fasten the pump directly to the cover.
− Insert the sponge into the cover.
Pos: 105 /Alle Produkte/Dummy_module/===== Seitenwechsel ===== @ 0\mod_1125648978015_0.doc @ 1631 @
10

Publicidad

Tabla de contenido
loading

Tabla de contenido