Installation Instructions; Description Of Connections - Nice WIL Manual De Instrucciones

English

2.1) INSTALLATION INSTRUCTIONS:

When installing the "WIL" road boom gate, all the instructions given in the enclosed instruction manual must be followed. It is
necessary to underline that there are standards, laws and regulations that establish limits and ways to make systems: please
comply strictly with all the applicable standards.
Do not install the "Wil" boom gate unless all the standards regarding the automatic gate category have been complied with!
Install all the control (key selector switch or push button panel) and safety devices (emergency stop, photoelectric cells, sensitive
edges and flashing lights) after which do the wiring following the diagram:
Fig. 3: Wiring diagram
NOTE:
Only qualified, expert personnel must carry out the installation and subsequent maintenance which must be in compliance with
the DPR N° 46 dated 5/3/1990 and in total observance of the UNI 8612 standards and following the best indications dictated by
"expert workmanship". Whoever carries out these jobs shall be held responsible for any damage caused.
2.2) DESCRIPTION OF THE CONNECTIONS:
Here is a brief description of the possible connections on the unit to the outside:
1-2 : 230 V a.c.
3-4 : Flashing light
5-6 : 24 V d.c.
7 : Common
8 : Courtesy Light
9 : C.A. Indicator
10 : Stop
11 : Photocell
12 : Photocell2
13 : Step-by-Step
14 : Open-Timer
15 : Close
41-42 : 2nd radio channel = Output for the second radio receiver channel if existing
43-44 : Antenna
The remaining connections are done in the factory but for the sake of completeness here is the list:
TRANS.PRIM.
TRANS.SECOND.
MOTOR
There are an additional two slots for optional cards:
RADIO = Slot for Nice radio receivers
CHARGE = Slot for battery charge card
14
STOP
PAUSE
AMPERE
TIME
FUNCTIONS
OK
COURTESY
LIGHT
FCA
FUSE
FCC
1 A
FUSE
8 A
SECONDARY TRANSFORMER
= 230 V a.c. 50/60 Hz
= Output for connection to the 24 V d.c. flashing light, maximum lamp power: 25 W
= 24 V d.c. output for supplying accessories (Photocell, Radio, etc.) maximum 200 mA
= Common for all inputs (terminal 6 can also be used as the Common)
= 24 V d.c. output for the courtesy light, maximum output power 10 W
= 24 V d.c. output for bar open indicator light, maximum indicator power 10 W
= Input with STOP function (Emergency, shutdown or extreme safety)
= Input for safety devices (Photocells, pneumatic edges)
= Input for safety devices with triggering in the opening phase (Photocells, pneumatic edges)
= Input for cyclic functioning (OPEN STOP CLOSE STOP)
= Input for opening (which can be timer controlled)
= Input for closing
= Input for the radio receiver antenna
= Primary of the power transformer
= Secondary of the power transformer
= Output for 24 V d.c. motor connection
SLOWING
DOWN FORCE
WORKING
44
ANTENNA
FORCE
43
42
2ND CH
RADIO
41
CLOSE
15
CLOSE
OPEN (TIMER) 14
OPEN (TIMER)
STEP-BY-STEP 13 STEP-BY-STEP
12 PHOTOCELL 2
PHOTOCELL 2
11 PHOTOCELL
PHOTOCELL
10 STOP
STOP
9 BAR OPEN INDICATOR
8 COURTESY LIGHT
7 COMMON
6 + (24v)
24 Vcc
max 200 mA
5 - (0 v)
4 LUCY 24 Vcc
+
max 25 W
-
3
FUSE
2
230 Vac
3,15 A
50-60 Hz
1
PRIM. TRANSFORMER