Formato De Datos Midi - Yamaha N-100 Manual De Instrucciones

MIDI Data Format / MIDI-Datenformat /
Format des données MIDI / Formato de datos MIDI
If you're already very familiar with MIDI, or are using a computer to control your music hardware with computer-generated MIDI
messages, the data provided in this section can help you to control the N-100.
Falls Sie bereits mit MIDI vertraut sind oder einen Computer zur Erzeugung von MIDI-Steuermeldungen für die Instrumente verwenden,
können Sie sich zur Steuerung des N-100 nach den im folgenden Abschnitt aufgeführten Spezifikationen richten.
Si vous êtes très familier avec l'interface MIDI ou si vous utilisez un ordinateur pour commander votre matériel de musique au moyen de
messages MIDI générés par ordinateur, les données suivantes vous seront utiles et vous aideront à commander le N-100.
SI usted está ya familiarizado con MIDI, o si emplea una computadora para controlar sus aparatos musicales con mensajes MIDI
generados por computadora, los datos proporcionados en esta sección le ayudarán a controlar la N-100.
1. NOTE ON/OFF
Data format: [9nH] -> [kk] -> [vv]
9nH = Note ON/OFF event (n = channel number)
kk = Note number (Transmit: 09H–78H = A-2–C8 /
Receive: 00H–7FH = C-2–G8)
vv = Velocity (Key ON = 01H–7FH, Key OFF = 00H)
Data format: [8nH] -> [kk] -> [vv] (reception only)
8nH = Note OFF event (n = channel number)
kk = Note number: 00H–7FH = C-2–G8)
vv = Velocity
2. CONTROL CHANGE
Data format: [BnH] -> [cc] -> [vv]
BnH = Control change (n = channel number)
cc = Control number
vv = Data Range
(1) Bank Select
ccH Parameter
00H Bank Select MSB
20H Bank Select LSB
Bank selection processing does not occur until receipt of
next Program Change message.
(2) Main Volume
ccH Parameter
07H Volume MSB
(3) Expression (reception only)
ccH Parameter
0BH Expression MSB
(4) Sustain
ccH Parameter
40H Sustain MSB
(5) Sostenuto (reception only)
ccH Parameter
42H Sostenuto
(6) Soft Pedal (reception only)
ccH Parameter
43H Soft Pedal
(7) Effect1 Depth (Reverb Send Level)
ccH Parameter
5BH Effect1 Depth
Adjusts the reverb send level.
(8) Effect4 Depth (Variation Effect Send Level)
ccH Parameter
5EH Effect4 Depth
(9) RPN
65H RPN
64H RPN
06H Data Entry
26H Data Entry
60H Data
61H Data
* Parameters that are controllable with RPN:
• Coarse Tune
• Fine Tune
• Pitch Bend Range
Data Range (vvH)
00H:Normal
00H...7FH
Data Range (vvH)
00H...7FH
Data Range (vvH)
00H...7FH
Data Range (vvH)
00H...7FH
Data Range (vvH)
00H...3FH:off, 40H...7FH:on
Data Range (vvH)
00H...3FH:off, 40H...7FH:on
Data Range (vvH)
00H...7FH
Data Range (vvH)
00H...7FH
MSB
LSB
MSB
LSB
Increment
Decrement
N-100 Owner's Manual / Bedienungsanleitung / Mode d'emploi / Manual de instrucciones
3. MODE MESSAGES
Data format: [BnH] -> [cc] -> [vv]
BnH = Control event (n = channel number)
cc = Control number
vv = Data Range
(1) All Sound Off
ccH Parameter
78H All Sound Off
(2) Reset All Controllers
ccH Parameter
79H Reset All Controllers
Resets controllers as follows.
Controller
Expression
Sustain Pedal
Sostenuto
Soft Pedal
(3) Local Control (reception only)
ccH Parameter
7AH Local Control
(4) All Notes Off
ccH Parameter
7BH All Notes Off
Switches OFF all the notes that are currently ON on the spec-
ified channel. Any notes being held by the sustain or soste-
nuto pedal will continue to sound until the pedal is released.
(5) Omni Off (reception only)
ccH Parameter
7CH Omni Off
Same processing as for All Notes Off.
(6) Omni On (reception only)
ccH Parameter
7DH Omni On
Same processing as for All Notes Off.
(7) Mono (reception only)
ccH Parameter
7EH Mono
Same processing as for All Sound Off.
(8) Poly (reception only)
ccH Parameter
7FH Poly
Same processing as for All Sound Off.
• When Control Change is turned OFF, Control Change mes-
sages will not be transmitted or received.
• Local on/off, OMNI on/off are not transmitted. (The appropri-
ate note off number is supplied with "All Note Off" transmis-
sion).
• When a voice bank MSB/LSB is received, the number is
stored in the internal buffer regardless of the received order,
then the stored value is used to select the appropriate voice
when a program change message is received.
• Poly mode is always active. This mode will not change when
the instrument receives a MONO/POLY mode message.
Data Range (vvH)
00H
Data Range (vvH)
00H
Value
127 (max)
0 (off)
0 (off)
0 (off)
Data Range (vvH)
00H (off), 7FH (on)
Data Range (vvH)
00H
Data Range (vvH)
00H
Data Range (vvH)
00H
Data Range (vvH)
00H
Data Range (vvH)
00H
33