Rigid catcher (model CE30M2, CE30P2, CE35M2 and CE35P)
It is necessary to join the upper half to lower half. After joining, do not try to separate them, as this may
damage the catcher [Fig. 21, Pag. 09].
Placing the catcher on the mower
Both types of catchers [bag and rigid] are attached in the same manner: raise the deflector (1) and attach
the catcher to chassis [Fig. 22, Pag. 09].
Always keep the grass catcher or baffle in the correct position during work.
Check whether the mower electric tension is the same as the electric mains.
Plug the cord in the switch and cord attach.
For your safety and to prevent the cord from getting unplugged while the work is being done, bend the cable
and run it through the cable attach hole and fit it to the catch; only then connect the cord to the mower plug
[Fig. 23, Pag. 09], [Fig. 24, Pag. 09].
Press the yellow button [Fig. 25, Pag. 10]. Pull the lever towards the arm. Once that is done the yellow button can
be released.
To turn the mower off, let go of the lever [Fig. 26, Pag. 10].
Switch the engine on according to previous instructions and keep your feet away from the blade. Start the engine
with the cutting blade free. Never start the mower directly on tall grass.
To ensure the engine's brake system durability, the lawn mower must keep running for at least 45 seconds, and
when it is turned off, you must wait 15 seconds before turning it on again.
After switching the engine off, the blade will stop turning in less than 3 seconds. This procedure may cause
some noise or a slight vibration, which is considered normal. Keep hands and feet away from cutting blade.
Power cord gauge
Engine
127 V
1,100 W
2 x 2.5 mm²
1,300 W
2 x 2.5 mm²
1,800 W
2 x 2.5 mm²
2,500 W
2 x 4.0 mm²
The use of unauthorized cords may damage the engine and is not covered by the warranty.
SETTING THE CUTTING HEIGHT
Models CE30M, CE30M2, CE30P2, CE35M, CE35M2 and CE35P
The settings are on the chassis of the lawn mower. To set the cutting height move the wheel height to one of the
3 adjustment positions (23 mm - 38 mm - 53 mm). Try to set the same setting position for the height of
both the front and rear wheels of the lawn mower [Fig. 27, Pag. 11].
OPERATION AND FORM OF USAGE
20 m
220 V
127 V
2 x 1.5 mm²
2 x 2.5 mm²
2 x 1.5 mm²
2 x 2.5 mm²
2 x 2.5 mm²
2 x 4.0 mm²
2 x 2.5 mm²
2 x 6.0 mm²
30 m
220 V
127 V
2 x 1.5 mm²
2 x 4.0 mm²
2 x 1.5 mm²
2 x 4.0 mm²
2 x 2.5 mm²
2 x 6.0 mm²
2 x 2.5 mm²
2 x 8.0 mm²
40 m
50 m
220 V
127 V
2 x 1.5 mm²
2 x 6.0 mm²
2 x 1.5 mm²
2 x 6.0 mm²
2 x 2.5 mm²
2 x 6.0 mm²
2 x 2.5 mm²
2 x 8.0 mm²
220 V
2 x 1.5 mm²
2 x 1.5 mm²
2 x 2.5 mm²
2 x 2.5 mm²
22