Uline H-2185 Guia De Inicio Rapido
Ocultar thumbs Ver también para H-2185:

Publicidad

Idiomas disponibles

Idiomas disponibles

π
H-2185, H-2186
corrosion resistant
pallet truck
WarninG! operator must read and understand
instructions here and on truck prior to use.
On the handle of the pallet truck, you will find the control
lever, which can be set in three positions.
(See Figure 1)
Figure 1
- LOWER = to lower the forks
- NEUTRAL = to move the load
- RAISE = to raise the forks
PAGE 1 OF 6
1-800-295-5510
uline.com
technical data
Model
Capacity
Max. Fork Height
Min. Fork Height
Fork Length
Overall Fork Width
Fork Wheel Diameter
Steering Wheel Diameter
Net Weight
operation
h-2185
5,500 lbs.
7.5"
3"
48"
27"
3" Polyurethane
3" Polyurethane
7" Polyurethane
7" Polyurethane
173 lbs.
1.
If the forks elevate while pumping in the NEUTRAL
position, turn the setting screw clockwise until
pumping the handle does not raise the forks and the
NEUTRAL position functions correctly.
2. If the forks descend while pumping in the NEUTRAL
position, turn the setting screw counterclockwise until
the forks do not lower.
3. If the forks do not descend when the control lever is in
the LOWER position, turn the setting screw clockwise
until raising the control lever lowers the forks. Then
check the NEUTRAL position as per step 1 and 2.
4.
If the forks do not lift while pumping in the RAISE
position, turn the setting screw counterclockwise
until the forks elevate while pumping in the RAISED
position. Then check the NEUTRAL and LOWER
positions as per steps 1, 2 and 3.
note: When viewing the truck from the handle
side, the setting screw is located on the right
side of the pump above the right wheel. the
truck will lower faster or slower depending on
how far in or out the screw is adjusted.
Para Español, vea páginas 4-6.
h-2186
5,500 lbs.
7.5"
3"
48"
27"
157 lbs.
0214 IH-2185

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Uline H-2185

  • Página 1 Para Español, vea páginas 4-6. π H-2185, H-2186 1-800-295-5510 uline.com corrosion resistant pallet truck technical data Model h-2185 h-2186 Capacity 5,500 lbs. 5,500 lbs. Max. Fork Height 7.5" 7.5" Min. Fork Height 3" 3" Fork Length 48" 48" Overall Fork Width 27"...
  • Página 2 Maintenance DAILy CHECk AND MAINTENANCE CHECk THE OIL LEvEL EvERy SIx MONTHS. THE OIL CAPACITy Daily checks of the pallet truck can limit wear and tear IS AbOUT 0.3L. RESTORE THE FLUID LEvEL TO 5MM bELOW on the unit. Pay special attention to the wheels, axles, THE TOP;...
  • Página 3 π CHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA • SEATTLE • MEXICO • CANADA 1-800-295-5510 uline.com PAGE 3 OF 6 0214 IH-2185...
  • Página 4: Datos Técnicos

    π H-2185, H-2186 01-800-295-5510 uline.mx patÍn hidrÁulico resistente a la corrosiÓn datos tÉcnicos Modelo h-2185 h-2186 Capacidad 5,500 lbs. 5,500 lbs. Altura Máx. de Horquilla 7.5" 7.5" Altura Mín. de Horquilla 3" 3" Longitud de Horquilla 48" 48" Ancho Total de Horquillas 27"...
  • Página 5: Mantenimiento

    ManteniMiento ACEITE levante la palanca a la posición LOWER, y luego mueva la asa hacia arriba y abajo varias veces. Revise el nivel de aceite cada seis meses. La capacidad REvISIÓN DIARIA y MANTENIMIENTO de aceite es aproximadamente 0.3L. Restaure el nivel de líquido a 5mm abajo del borde;...
  • Página 6: Solución De Problemas

    π CHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA • SEATTLE • MEXICO • CANADA 01-800-295-5510 uline.mx PAGE 6 OF 6 0214 IH-2185...

Este manual también es adecuado para:

H-2186

Tabla de contenido