Hob Frame; The Tipp Control; Fixing Malfunctions; Normal Noise While The Appliance Is Working - NEFF T4.T.0 Serie Instrucciones De Uso

Glass scraper
Remove dried-on food remains using a glass scraper.
Release the scraper safety catch
1.
Use the blade to clean the hob surface
2.
Do not attempt to clean the hob surface with the base of the
scraper. This could result in scratching.
ã=
Risk of injury!!
The blade is extremely sharp. Risk of cuts. Protect the blade
when not in use. Replace the blade immediately when any
imperfections are found.
Care of the appliance
Apply an additive to protect and preserve the hob. Follow the
advice and warnings provided with the product.

Fixing malfunctions

Malfunctions are generally caused by minor faults. Before
contacting the Technical Assistance Service, ensure you have
read the following recommendations and warnings.
Indicator Malfunction
none The electric power supply has been cut off. Check other electrical appliances to check whether there has been a
The appliance has not been properly
connected following the connection
diagram.
Electronic system malfunction.
The control panel is wet or an object is
flashing
"
resting on it.
Electronic system malfunction.
+ number /
"§
š + number /
+ number
¡
The Tipp control was dragged instead of
"§„‰
slanting it towards the required hotplate
There is an internal error in the system.
/
"‹ "Š
The electronic system has overheated and
"ƒ
the related hotplate has been switched off.
The electronic system has overheated and
"...
all of the hotplates have been turned off.
Incorrect voltage supply, outside the
—‚
normal operating limits.
The hotplate has overheated and switched
—ƒ / —„
off to protect its working surface.
* If the indicator persists, call the Technical Assistance Service.
Do not rest hot pans on the control panel.

Normal noise while the appliance is working

Induction heating technology is based on the creation of
electromagnetic fields that generate heat directly at the base of
the pan. Depending on how the pan has been manufactured,
these may produce certain noises or vibrations such as those
described below:
A deep humming sound as in a transformer
This noise is produced when cooking on a high power level. It
is caused by the amount of energy transferred from the hob to
the pan. The noise disappears or becomes faint when the
power level is lowered.

Hob frame

In order to avoid damage to the hob frame, follow the
indications below:
Use only slightly soapy hot water
■
Do not use sharp or abrasive products
■
Do not use a glass scraper
■

The Tipp control

For cleaning the Tipp control, warm water and a little soap is
recommended. Do not use abrasive or corrosive cleaning
products. Do not clean the Tipp control in a dishwasher or in
washing up water. Otherwise, it could be damaged.
Measure
power cut.
Check that the appliance has been connected properly according to
the connection diagram.
If the malfunction is not resolved by the above checks, contact the
Technical Assistance Service.
Dry the control panel area or remove the object.
Disconnect the range from the mains. Wait about 30 seconds, then
connect it again.*
Wait a few seconds, then switch on the range and hotplate properly
once again.
Disconnect the range from the mains. Wait about 30 seconds, then
connect it again.*
Wait for the electronic system to cool down. Then push any symbol
on the range.*
Please contact your local electricity company.
Wait until the electronic system has cooled down sufficiently before
switching the hotplate back on.
A low whistling sound
This noise is produced when the pan is empty. It disappears
when water or food is added to the pan.
A crackling sound
This noise occurs in pans which are made from different
materials superimposed on one another. It is caused by the
vibrations that occur ajoining surfaces of the different
superimposed materials. The noise comes from the pan. The
amount of food and cooking method can vary.
25