Function Modes - Cardin Elettronica BL Serie Manual Del Usuario

REMOTE CONTROL (fig. 14 - page 8)
The system can be remotely activated using radio control devices; to set the
two functions to channels A-B-C-D use the selection jumper "J4":
- in position "A" function 1 is selected, SEQUENTIAL COMMAND;
- in position "B" function 2 is selected, CH2 (binding posts 9, 10) only if
J5
The sequential command may be set (dip "1") to "open-block-close-block"
or "open-close".
Memory module (MM)
This is extractable, furnished with a non volatile EEPROM type memory
and contains the transmitter codes and allows you to memorise up to 300
codes.
The programmed codes are maintained in this module even during black-
outs.
Before memorising the transmitters for the first time remember
to cancel the entire memory content. If the electronic card has
to be replaced due to failure, the module can be extracted from
it and inserted into the new card. Make sure that the module is
correctly inserted as shown on page 8.
Signal LED "L4" (pag. 8):
Flashing quickly: cancels a single code
Flashing slowly: memorises a single code
Permanently lit: memory full.
TRANSMITTER CODE MANAGEMENT
Memorising a channel (pag. 8):
slowly.
2. At the same time activate the transmitter which is to be memorised.
P2 MEMO
4. Release the MEMO button: The LED will continue to flash.
5. Activate the transmitter again (same transmitter, same channel; if the
channel is different or it is a different transmitter the memorisation attempt
will abort without success).
that the transmitter has been correctly memorised.
Notes: It is not possible to memorise a code which is already in memory: if
you attempt this, the LED will switch off when you activate the transmitter
continue the memorising procedure.
If after activating the transmitter for the first time you wait for more than fifteen
seconds without activating the transmitter a second time the memorisation
attempt will abort without success.
Cancelling a channel (pag. 8):
quickly.
2. Activate the transmitter channel that is to be cancelled.
3. The LED will remain lit for 2 seconds, indicating that the transmitter has
been cancelled.
Notes: If the user that you wish to cancel is not in memory, the LED will stop
cancellation procedure.
For both the memorisation and cancellation procedures, if the button is
released before activating the transmitter the procedure will abort.
C) Cancelling all user codes from memory (pag. 8):
onds.
L4
onds).
L4
Note: When the memory is almost full the time required to search for a user
code could take up to 1 second from when the command was received. If
LED "L4" remains lit memory is completely full. To memorise a new transmit-
ter you will first have to cancel a code from memory.
P2 MEMO L4
L4
L4
P2 MEMO will you be able to
P3 DEL L4
P3
P2+P3
Memorising ulterior channels via radio
J3
2. Using a transmitter, in which at least one
A, B, C or D
been memorised in the receiver, press
the button in the transmitter as shown in
figure.
Note: all the receivers within range when the channel button is pressed (and
which have at least one of the transmitter channel buttons memorised) will
3. Press one of the channel buttons on the same transmitter. The receivers
which do not contain that channel code will sound a five-second long
The receivers which contain the channel code will sound a one-second
4. Press the previously chosen channel buttons on the transmitter which you
after which the receiver will be ready to receive another code.
5. To leave the programming mode wait for 3 seconds without pressing any
buttons.
programming mode.
Note: When the memory is entirely occupied the buzzer will sound 10 rapid
L4
when the memory is full.
CONNECTING THE ANTENNA
Connect an ANS400 tuned antenna using a coaxial cable RG58 (impedance
50 ) with a maximum length of 15 m.

FUNCTION MODES

1) Automatic
the door is completely closed the opening command will start a complete
cycle which will end with automatic reclosing.
Automatic reclosing starts after the programmed pause period has elapsed
when the opening cycle has been completed or straight away after the
intervention of a photoelectric cell (the intervention of a photoelectric cell
causes the pause time to be reset).
During the pause time the symbol
the blocking button during this period will stop automatic reclosing and
consequently stop the display from flashing.
The indicator light remains lit until the closing manoeuvre has terminated.
Note: the courtesy light switches on each time a movement command is given
(both via cable or via radio) and switches off 30 seconds after the manoeuvre
has been completed
2) Semiautomatic
Work cycle control using separate opening and closing commands. When
the door has reached the completely open position the system will wait until
it receives a closing command either via an external control button or via
radio control, before completing the cycle.
The indicator light remains lit until the closing manoeuvre has terminated.
-
3) Manual manoeuvring with released motors
Releasing the motor the gate can be moved by hand; in this stage the pro-
-
grammer does not control the position of the gate leaves and so when the
next movement command is given (after the motors have been blocked again)
automatic repositioning will take place due to the positioning error.
Attention! If a command is given while the motor is released the
symbol or
motor has been released.
22
J3
B1
programming via radio" mode.
programming via radio
programming via radio
2
will flash on the display and pressing
J5 1
2
will appear on the display depending on which
ON
.
OFF