General Safety - Silverline 321030 Manual De Instrucciones

321030
Sound
The noise directive was introduced to protect against the risk to health and safety arising or likely to
arise from exposure to noise and risk of hearing. The Directive can be used to define noise exposure
and the physical parameters, such as peak sound pressure and daily and weekly exposure level.
Particular attention should be taken to exposure level and duration.
For more information on the Noise Directives 2003/10/EC and 2000/14/EC, please visit The
European Agency for Safety and Health at work - www.osha.europa.eu.
Vibration
The European Physical Agents (Vibration) Directive 2002/44/EC was introduced to control the
exposure of vibration at work. The Directive enables users of tools to make informed decisions on
the amount of time spent working. Those who regularly operate high vibration equipment over a
sustained period of time are at a higher risk of health problems. ISO 28927-3 measures vibration
in three directions which is known as tri-axial or vector sum measurement. When operating high
vibration equipment, ensure not to exceed exposure levels. For more details on The Vibration
Directive 2002/44/EC please visit The European Agency for Safety and Health at work -www.osha.
europa.eu

General Safety

• For multiple hazards, read and understand the safety instructions before installing, operating,
repairing, maintaining, changing accessories on, or working near this tool. Failure to do so can
result in serious bodily injury
• Only qualified and trained operators should install, adjust, or use this tool
• Do not modify this tool. Modifications can reduce the effectiveness of safety measures and
increase the risks to the operator
• Do not discard the safety instructions; give them to the operator
• Do not use this tool if it has been damaged
• Tools shall be inspected periodically to verify that the ratings and markings required by this part
of ISO 11148 are legibly marked on the tool. The employer/user should contact the manufacturer
to obtain replacement marking labels when necessary
WARNING: This appliance is not intended for use by persons (including children) with reduced,
physical or mental capabilities or lack of experience or knowledge unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children must be supervised to ensure that they do not play with the appliance.
Projectile Hazards
• Be aware that failure of the workpiece or accessories, or even of the inserted tool itself, can
generate high-velocity projectiles
• Always wear impact-resistant eye protection during operation of this tool. The grade of protection
required should be assessed for each use
• For overhead work, wear a safety helmet
• The risks to others should also be assessed at this time
• Ensure that the workpiece is securely fixed
Entanglement Hazards
• Choking, scalping and/or lacerations can occur if loose clothing, personal jewellery, neck wear,
hair or gloves are not kept away from the tool and its accessories
Operating Hazards
• Use of the tool can expose the operator's hands to hazards, including cuts, abrasions and heat
• Wear suitable gloves to protect hands
• Operators and maintenance personnel should be physically able to handle the bulk, weight and
power of the tool
• Hold the tool correctly; be ready to counteract normal or sudden movements and have both
hands available
• Maintain a balanced body position and secure footing
• Release the start-and-stop device in the case of an interruption of the energy supply
• Use only lubricants recommended by the manufacturer
• Personal protective safety glasses should be used; suitable gloves and protective clothing are
recommended
• Avoid direct contact with moving parts in order to prevent pinching or cutting of hands or other
body parts. Wear suitable gloves to protect hands
• There is a risk of electrostatic discharge if used on plastic and other non-conductive materials
Air Sheet Metal Shears
Repetitive Motions Hazards
• When using this tool to perform work-related activities, the operator can experience discomfort in
the hands, arms, shoulders, neck or other parts of the body
• While using this tool, the operator should adopt a comfortable posture whilst maintaining secure
footing and avoiding awkward or off-balance postures. The operator should change posture
during extended tasks; this can help avoid discomfort and fatigue
• If the operator experiences symptoms such as persistent or recurring discomfort, pain, throbbing,
aching, tingling, numbness, burning sensations or stiffness, these warning signs should not be
ignored. The operator should inform the employer and consult a qualified health professional
Accessory Hazards
• Disconnect the tool from the energy supply before fitting or changing the inserted tool or
accessory
• Avoid direct contact with the inserted tool during and after use, as it can be hot or sharp
• Use only sizes and types of accessories and consumables that are recommended by the
manufacturer of this tool; do not use other types or sizes of accessories or consumables
Workplace Hazards
• Slips, trips and falls are major causes of workplace injury. Be aware of slippery surfaces caused by
use of the tool and also of trip hazards caused by the air line or hydraulic hose
• This tool is not intended for use in potentially explosive atmospheres and is not insulated against
contact with electric power
• Ensure that there are no electrical cables, gas pipes, etc., which can cause a hazard if damaged
by use of the tool
Dust & Fume Hazards
• Dust and fumes generated when using this tool can cause ill health (for example cancer, birth
defects, asthma and/or dermatitis); risk assessment and implementation of appropriate controls
for these hazards are essential
• Risk assessment should include dust created by the use of the tool and the potential for
disturbing existing dust
• Operate and maintain this tool as recommended in these instructions, to minimise dust or
fume emissions
• Direct the exhaust so as to minimise disturbance of dust in a dust-filled environment
• Where dust or fumes are created, the priority should be to control them at the point of emission
• Select, maintain and replace the consumable/inserted tool as recommended in the instruction
handbook, to prevent an unnecessary increase in dust or fumes
• Use respiratory protection in accordance with employer's instructions and as required by
occupational health and safety regulations
Noise Hazards
• Exposure to high noise levels can cause permanent, disabling hearing loss and other problems,
such as tinnitus (ringing, buzzing, whistling or humming in the ears). Therefore, risk assessment
and implementation of appropriate controls for these hazards are essential
• Appropriate controls to reduce the risk can include actions such as damping materials to prevent
workpieces from 'ringing'
• Use hearing protection in accordance with employer's instructions and as required by
occupational health and safety regulations
• Operate and maintain this tool as recommended in the instruction handbook, to prevent an
unnecessary increase in the noise level
• Select, maintain and replace the consumable/inserted tool as recommended in the instruction
handbook, to prevent an unnecessary increase in noise
• If the tool has a silencer, always ensure it is in place and in good working order when the tool
is being operated
Vibration Hazards
This information shall draw attention to vibration hazards that have not been eliminated by design
and construction and remain as residual vibration risks. It shall enable employers to identify the
circumstances in which the operator is likely to be at risk from vibration exposure If the vibration-
emission value obtained using ISO 28927-3 does not adequately represent the vibration emission
in the intended uses (and foreseeable misuses) of the machine, additional information and/or
warnings shall be supplied to enable the risks arising from vibration to be assessed and managed.
• Exposure to vibration can cause disabling damage to the nerves and blood supply of the hands
and arms
• Wear warm clothing when working in cold conditions and keep your hands warm and dry
• If you experience numbness, tingling, pain or whitening of the skin in your fingers or hands, stop
using the tool, inform your employer and consult a physician
• Operate and maintain the tool as recommended in the instruction handbook, to prevent an
unnecessary increase in vibration levels
• Hold the tool with a light but safe grip, taking account of the required hand reaction forces,
because the risk from vibration is generally greater when the grip force is higher
silverlinetools.com
7