Eco Function - Kenwood FPM810 Serie Instrucciones

to use your food processor
1 Fit the bowl to the power unit. Place the handle towards the
back on the right hand side and turn clockwise
locks.
2 Fit an attachment over the bowl drive shaft.
Note: Detachable drive shaft
when using the discs, mini bowl, whisk, folding
tool and citrus juicer.
Always fit the bowl and attachment onto the processor
G
before adding ingredients.
3
3 Fit the lid - ensuring the top of the drive shaft/tool locates
into the centre of the lid.
The processor will not operate if the bowl or lid
G
are not fitted correctly into the interlock. Check
that the feed tube and bowl handle are situated
to the right hand side.
4 Plug in. The Power On light will come on and flash until the
bowl and lid are fitted correctly. Select one of the following
options: -
Auto Button – the light will come on when the Auto Button is
pressed and the optimum speed for the attachment will be
automatically selected.
Speed Control – manually select the required speed (refer to
the recommended speed chart).
Pulse – use the pulse (P) for short bursts. The pulse will
operate for as long as the control is held in position.
5 At the end of processing turn the speed control to the 'O' off
position or if using the Auto press the button and the light
will go out.
The Power On light will flash if either the lid or
G
bowl are not fitted or incorrectly fitted.
The Auto Button will not operate if a speed is
G
selected on the speed control.
Always switch off and unplug before removing the
G
lid.
important
Your processor is not suitable for crushing or grinding coffee
G
beans, or converting granulated sugar to caster sugar.

Eco function

If the food processor is left plugged in for over 30 minutes
without being used, it will go into standby mode to reduce
energy consumption.
The Power On light will pulse slowly and the food processor
G
will not operate until one of the following actions are carried
out:-
The Auto Button is pressed.
G
The speed control is turned to a speed and then turned
G
back to the 'O' off position.
The light will change to being constantly lit when ready to
use.
Note: If the bowl or lid are not engaged into the interlock the
power on light with pulse more rapidly than the Eco function.
1
until it
2
should be fitted
weighing function
Your food processor is fitted with a built in weighing function
to allow ingredients to be weighed straight into the bowl or
blender goblet.
The Maximum weighing capacity is 3Kg. This is the total
G
weight of all the ingredients including the weight of the bowl
or goblet.
to use the weighing function
1 Always fit the bowl, detachable drive shaft and attachment
or blender goblet onto the power unit before adding
ingredients.
2 Plug in – the display screen will
remain blank.
3 Press the ON/ZERO button once
and the display screen will light up.
4 Press the (kg/lb) button to select
either grams or ounces. The
display will default to kg/g when
first switched on.
The unit weighs in 2g increments
G
and teaspoon/tablespoon
measures are recommended for
weighing small quantities.
5 Check the display shows 'O', if
not, zero by pressing the ON/ZERO button. Then weigh the
required ingredients straight into the bowl or goblet. After the
weight is displayed, press the ON/ZERO button and the
display will return to 'O'. Add the next ingredients and that
weight will be displayed. Repeat until all ingredients are
weighed.
G If the display is not zeroed and either the ingredients or the
bowl/attachment/lid are removed the display will show [ - - -
-] to represent a minus reading.
To zero press the ON/ZERO button once.
6 Add the lid and select a speed to operate the processor.
During operation the display screen will freeze [- - - -] until
G
the speed control returned to the 'O' off position.
After processing the last weight will be displayed on the
G
screen when the speed control is returned to the 'O' off
position. Note: The weight of the lid will be included if the
display is not zeroed before switching on.
The weight of any additional ingredients added down the
G
feed tube whilst the processor is running will not be shown
on the display screen.
4