Ce Declaration Of Conformity; Important Notice For The Installer; General Safety Regulations - FAAC 595 I Guía Para El Usuario

CE DECLARATION OF CONFORMITY FOR MACHINERY
Manufacturer: FAAC S.p.A.
Address: Via Benini, 1
40069 - Zola Predosa
BOLOGNA-ITALY
The 595 I / S operator,
Declares that:
• is intended to be incorporated into machinery, or to be assembled with other machinery to constitute machinery
in compliance with the requirements of Directive 89/392 EEC, and subsequent amendments 91/368/EEC, 93/44/EEC
and 93/68/EEC;
• complies with the essential safety requirements in the following EEC Directives:
73/23 EEC and subsequent amendment 93/68/EEC.
89/336 EEC and subsequent amendments 92/31 EEC and 93/68/EEC
and furthermore declares that unit must not be put into service until the machinery into which it is incorporated or
of which it is a component has been identified and declared to be in conformity with the provisions of Directive
89/392/EEC and subsequent amendments enacted by the national implementing legislation, Presidential Decree
no. 459 dd. 24 July 1996.
Bologna, 01 January 2006
1) WARNING! FAAC strongly recommends to follow these instructions
literally for the safety of persons. Improper installation or misuse
of the product will cause very serious damages to persons.
2) Read the instructions carefully before installing the product.
3) Packaging material (plastic, polystyrene etc.) is a potential
hazard and must be kept out of reach of children.
4) Keep these instructions for future reference.
5) This product has been designed and manufactured only for
the use stated in this manual. Any other use not expressly set
forth will affect the reliability of the product and/or could be
source of hazard.
6) FAAC cannot be held responsible for any damage caused by
improper use or different from the use for which the automated
system is destined to.
7) Do not use this device in areas subject to explosion: the presence
of flammable gas or fumes is a serious hazard.
8) Mechanical constructive elements must comply with UNI8612,
CEN pr EN 12604 and CEN pr EN 12605 standards.
Countries outside the EC shall follow the regulations above
besides their national normative references in order to offer
the utmost safety.
9) FAAC cannot be held responsible for failure to observe technical
standards in the construction of gates and doors, or for any
deformation of the gates which may occur during use.
10) Installation must comply with UNI8612, CEN pr EN 12453 and
CEN pr EN 12635.
The degree of safety of the automated system must be C+E.
11) Before carrying out any operations, turn off the system's main
switch.
12) An omnipolar switch shall be provided for the installation with an
opening distance of the contacts of 3mm or more. Alternatively,
use a 6A thermomagnetic breaker with omnipolar switching.
13) Ensure that there is a differential switch up-line of the electrical
system, with a trip threshold of 0.03A.
(DIRECTIVE 89/392 EEC, ENCLOSURE II, PART B)
The Managing Director
A. Bassi

IMPORTANT NOTICE FOR THE INSTALLER

GENERAL SAFETY REGULATIONS

2
14) Check that the earthing plant is in perfect condition and
connect it to the metallic parts. Also earth the Yellow/Green
wire of the automated system.
15) The automated system is fitted with an anti-crush safety system
that is a torque control device. In any case, further safety
devices shall be installed.
16) The safety devices (e.g. photocells, sensitive edges, etc.)
protect areas where there is a mechanical movement Hazard,
e.g. crushing, entrapment and cutting.
17) Each installation must be fitted with at least one flashing light
(e.g. FAAC LAMP , MINILAMP etc.) as well as a warning plate
suitably fixed to the gate, besides the safety devices as per
point "16" above.
18) FAAC cannot be held responsible regarding safety and correct
functioning of the automated system in the event that parts
other than FAAC original parts are used.
19) Use only FAAC original spare parts for maintenance
operations.
20) Do not carry out any modifications to automation
components.
21) The installer must supply all information regarding manual
operation of the system in the event of an emergency and
provide the end-user with the "User's Guide" attached to the
product.
22) Keep out children or persons when the product is in
operation.
23) Keep out of reach of children the radio controls and any
control devices. The automated system could be operated
unintentionally.
24) The end-user must avoid any attempt to repair or adjust the
automated system personally. These operations must be carried
out exclusively by qualified personnel.
25) What is not explicitly stated in these instructions is not
permitted.