Protecting The Environment; Optional Accessories - DeWalt DWS778 Traducido De Las Instrucciones Originales

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 34
EN G LI S H
WARNING: If the saw blade is worn, replace it with a
new sharp blade.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
Before use, carefully check the upper blade guard, movable lower
blade guard as well as the dust extraction tube to determine that it will
operate properly. Ensure that chips, dust or workpiece particle cannot
lead to blockage of one of the functions.
In case of workpiece fragments jammed between saw blade and
guards disconnect the machine from the power supply and follow the
instructions given in section Mounting the Saw Blade. Remove the
jammed parts and reassembling the saw blade.
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
WARNING: To reduce the risk of injury, regularly clean
the table top.
WARNING: To reduce the risk of injury, regularly clean
the dust collection system.

Optional Accessories

WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
E
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
SUPPORT FOR LONG PIECES (FIG. 5)
• Always support long pieces.
• For best results, use the extension work support (DE7023) to
extend the table width of your saw (available from your dealer as
an option). Support long workpieces using any convenient means
such as saw-horses or similar devices to keep the ends from
dropping.
RANGE OF SAW BLADES AVAILABLE (RECOMMENDED BLADES)
Type of blade
Blade dimensions
DT1158 series 30
250 mm
DT4282 series 40
250 mm
DT4226 series 40
250 mm
DT4287 series 40
250 mm
DT4282 series 40
250 mm
Consult your dealer for further information on the appropriate
accessories.
30
WALT, recommended
E
Usage
For general purpose, ripping and
cross-cutting of wood and
plastics
TCG for use with aluminum
ATB for fine cutting of
manmade and natural wood
TCG for extra fine cutting of
manmade and natural wood
Aluminium cutting

Protecting the Environment

Separate collection. This product must not be disposed of
with normal household waste.
Should you find one day that your D
or if it is of no further use to you, do not dispose of it with household
waste. Make this product available for separate collection.
Separate collection of used products and packaging allows
materials to be recycled and used again. Re-use of
recycled materials helps prevent environmental pollution
and reduces the demand for raw materials.
Local regulations may provide for separate collection of electrical
products from the household, at municipal waste sites or by the retailer
when you purchase a new product.
D
WALT provides a facility for the collection and recycling of D
E
products once they have reached the end of their working life. To take
advantage of this service please return your product to any authorised
repair agent who will collect them on our behalf.
You can check the location of your nearest authorised repair agent by
contacting your local D
WALT office at the address indicated in this
E
manual. Alternatively, a list of authorised D
full details of our after-sales service and contacts are available on the
Internet at: www.2helpU.com.
WALT product needs replacement,
E
WALT
E
WALT repair agents and
E

Publicidad

Tabla de contenido
loading

Tabla de contenido