Stiga NJ 92 Serie Traducción Del Manual Original página 31

Ocultar thumbs Ver también para NJ 92 Serie:
Tabla de contenido

Publicidad

4.5 LIGHTS SWITCH (if fitted)
(Fig. 4.1 no.5)
For turning on the lights when the key (4.3) is in 
the «ON» position.
4.6 INDICATOR LIGHTS AND AUDIBLE
WARNING DEVICE ON THE DASH-
BOARD (Fig. 4.1 no.6).
–    T he sound warning signals that the grass 
catcher is full (see 5.4.6).
Machine with one indicator light
(Fig. 4.1 no.6a).
This lamp comes on when the key (4.3) is 
in the «ON» position and stays on while the 
machine is running.
–    W hen it flashes, it means that it is not 
ready to be started  (see 5.2).
Machine with 6 indicator light panel
(Fig. 4.1 no.6b)
The dashboard has a series of indicator
lights that are enabled with the ignition key 
(4.3) in the «ON» position.
–    W hen a warning light comes on, it indi-
cates:
a)    H and brake enabled;
b) grass catcher or rear discharge guard
missing;
c)    c utting means engaged;
d)    n o operator present;
e)    G ear in "neutral"; 
f)    f ault in battery charger (with engine run-
ning).
4.7 CUTTING MEANS ENGAGE AND
BRAKE CONTROLS (Fig. 4.1 no.7)
The mushroom switch allows you to engage the 
cutting means using the electromagnetic clutch:
     «A»  Pressed =    C utting means 
     «B»  Pulled =  Cutting means engaged  
–    I f you engage the cutting means without tak-
ing the necessary safety precautions, the 
engine shuts down and cannot be restarted 
(see 5.2).
–    I n disengaging the cutting means (Pos. «A»), 
a brake is simultaneously activated which 
stops their rotation within a few seconds.
disengaged
4.8 CUTTING HEIGHT ADJUSTMENT
LEVER (Fig. 4.1 no.8)
There are seven positions for this lever, shown 
as «1» to «7» on the label, which correspond to 
various heights between 3 and 8 cm.
–    T o go from one height to another, press the 
release button at the end of the lever.
4.9 GRASS CATCHER TIPPING LEVER
(if fitted) (Fig. 4.1 no.9)
This pull-out lever tips and empties the grass 
catcher. This means less work for the operator.
4.10 REVERSE GEAR CUTTING
CONSENT BUTTON (Fig. 4.1 no. 10)
By pressing and holding this button, it is pos-
sible to switch to reverse gear with the cutting 
means engaged without causing the engine to 
stop.
Mechanical transmission
4.21 CLUTCH / BRAKE PEDAL
(Fig. 4.2 no.21)
This pedal has two functions: during the first 
part of its travel it acts as a clutch, engaging
and disengaging drive to the wheels, and in 
the second part it acts as a brake on the rear 
wheels
IMPORTANT Do not keep the pedal half
way between clutch engagement or disen-
gagement, as this can cause overheating and
damage the transmission belt.
NOTE When the machine is in movement,
keep your foot off the pedal.
4.22 SPEED CHANGE LEVER
(Fig. 4.2 no.22)
This lever has seven positions for the 5 for-
ward speeds, the neutral position «N», and 
reverse «R».
To go from one speed to another, press the 
pedal (4.21) halfway and shift the lever as 
shown on the label.
WARNING!
when the machine has stopped.
8
Gear must be engaged

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Nj 102 serie

Tabla de contenido