Operating Instructions; Safety Recommendations; Why The Safety Devices Cut In; Preliminary Operations Before - Stiga NJ 92 Serie Traducción Del Manual Original

Ocultar thumbs Ver también para NJ 92 Serie:
Tabla de contenido

Publicidad

WARNING!
gaged when the machine has stopped.
Hydrostatic transmission:
4.31 BRAKE PEDAL (Fig. 4.3 no.31)
This pedal works the brake on the rear 
wheels.
4.32 CLUTCH PEDAL (Fig. 4.3 no.32)
This pedal engages drive in the wheels and 
controls the machine's forward and reverse 
speed.
–    T o engage forward gear just press it in the 
«F» direction with the tip of your foot, not-
ing that increasing the pressure on the
pedal progressively increases the speed 
of the machine.
–    R everse is engaged by pressing the pedal 
with the heel towards «R».
–    T he pedal automatically goes into neutral 
«N» when released.
WARNING!
gaged when the machine has stopped.
NOTE If the drive pedal is used, wheth-
er forwards or for reverse, when the parking
brake (4.4) is engaged, the engine stops.
4.33 HYDROSTATIC TRANSMISSION
DISENGAGEMENT LEVER
(Fig. 4.3 no.33)
This lever has two positions as shown on the 
label:
«A»  =    T ransmission engaged: for all uses, 
when moving and during cutting;
«B»  =    T ransmission disengaged: this 
makes it much easier to move the 
machine by hand, with the engine
turned off.
IMPORTANT To avoid damaging the
transmission unit, this operation must be car-
ried out only when the engine has stopped
with the pedal (4.32) at position «N".

5. OPERATING INSTRUCTIONS

5.1 SAFETY RECOMMENDATIONS

WARNING!
If the machine is likely to
be used mostly on sloping ground (never
steeper than 10°), fit counterweights (sup-
plied on request (see 8.1) beneath the cross-
Reverse must be en-
Reverse must be en-
member of the front wheels. These improve
stability at the front and reduce the chances
of tipping over.
IMPORTANT All the references relating to
the positions of controls are those described in
chapter 4.

5.2 WHY THE SAFETY DEVICES CUT IN

The safety devices work in two ways:
–    t hey prevent the engine from starting if all the 
safety requirements have not been met;
–    b y stopping the engine if even just one of the 
safety requirements is lacking. 
a) To start the engine, it is necessary that:
–    t he transmission is in "neutral";
–    a ll the cutting means are disengaged;
–    t he operator is seated.
b) The engine stops when:
–    t he operator leaves his seat;
–    t he grass catcher is lifted or the rear dis-
charge guard removed without disengaging 
the cutting means;
–    t he parking brake is engaged without disen-
gaging the cutting means;
–    t he speed change (see 4.22) or the drive 
pedal (see 4.32)  is activated with the parking 
brake on.

5.3 PRELIMINARY OPERATIONS BEFORE

STARTING WORK
Before starting to mow, it is necessary to carry 
out several checks and operations to ensure 
you can work efficiently and in maximum safety.
5.3.1 Seat adjustment (Fig. 5.1)
To change the seat position, loosen the four fix-
ing bolts (1) and slide it along the slots.
Once you have found the right position, tighten 
the four screws (1) thoroughly.
5.3.2 Tyre pressure (Fig. 5.2)
Having the right tyre pressure is the main condi-
tion for ensuring that the cutting-means assem-
bly is horizontal and mows evenly.
Unscrew the valve caps and connect a com-
pressed air line with a gauge to the valves and 
adjust the pressure to the indicated values.
5.3.3 Filling with oil and fuel
NOTE The type of oil and fuel to use is given
in the engine manual.
9

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Nj 102 serie

Tabla de contenido