Protecting The Environment - DeWalt DCMPS567 Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 56
EnGLIsh
a. Make sure pole saw is running at full speed before
making a cut. When starting a cut, place moving saw
chain 
14
against limb. Hold pole saw firmly in place to
avoid possible bouncing or skating (sideways movement)
of pole saw.
b. Guide pole saw using light pressure. Make first cut
152 mm from tree trunk on underside of limb. Use top of
guide bar 
13
to make this cut. Cut 1/3 through diameter
of limb. Then make the finish cut from the top. If you try
to cut off thick branches from the bottom, the branch
may close in and pinch the saw chain in the cut. If you try
to cut off thick branches from the top, without a shallow
undercut, the branch may splinter. Do not force pole saw.
The motor will overload and can burn out. It will do the
job better and safer at the rate for which it was intended.
c. Remove pole saw from cut while it is running at full
speed. Stop pole saw by releasing trigger switch 
Make sure saw chain has stopped before setting pole
saw down.
Saw Chain Sharpness

CAUTION: Sharp chain. Always wear protective gloves
when handling the chain. The chain is sharp and can cut
you when it is not running.
IMPORTANT: The chain cutters will dull immediately if they
touch the ground, stones, masonry or a nail while cutting.
To get the best possible performance from your chain saw it
is important to keep the teeth of the saw chain sharp. Chain
sharpening services are available from your nearest D
service center.
nOTE: Each time the saw chain is sharpened, it loses some
of the reduced kickback qualities and extra caution should be
used. It is recommended that a saw chain be sharpened no
more than four times.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.

WARNING:To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
Regular maintenance ensures a long effective life for the tool.
After every 10 minutes of use be sure to remove the battery (be
aware the chain and bar can be hot!) check the bar and chain for
correct tension and lubricate per Adjusting Chain Tension and
Chain Oiling.
52
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
4
.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories

WARNING: Since accessories, other than those offered
by D
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
WALT
e
Replacement chain and bar are available from your
nearest D
e
DCMPS567 requires replacement chain service part
number DT20667-QZ . Replacement 20 cm (8 inch) bar,
service part number DT20668-QZ.

Protecting the Environment

Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails to
produce sufficient power on jobs which were easily done before.
At the end of its technical life, discard it with due care for our
environment:
Run the battery pack down completely, then remove it from
the tool.
Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
WALT, have not been tested with this product, use
e
WALT service center.
WALT recommended
e

Publicidad

Tabla de contenido
loading

Tabla de contenido