SKIL MASTERS F0153900 Serie Manual Original página 9

preventive safety measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool's operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
SPECIFIC SAFETY INSTRUCTIONS FOR BENCH
GRINDERS
GENERAL
• This tool should not be used by people under the age of
16 years
• Never use the tool when cord is damaged; have it
replaced by a qualified person
• Connect this earthed power tool only to a properly
earthed power supply system; ensure that socket
and extension cable have a functional protective
conductor
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
• Inspect the extension cord periodically and replace it, if
damaged
• Only use the flanges which are supplied with this tool
• Always use the tool with grinding wheels on both spindles
• Do not work materials containing asbestos (asbestos
is considered carcinogenic)
• Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
• Certain kinds of dust are classified as carcinogenic (such
as oak and beech dust) especially in conjunction with
additives for wood conditioning; wear a dust mask and
work with a dust extraction device when
connectable
• Follow the dust-related national requirements for the
materials you want to work with
• Always disconnect plug from power source before
making any adjustment or changing any accessory
ACCESSORIES
• SKIL can assure flawless functioning of the tool only
when the correct accessories are used which can be
obtained from your SKIL dealer
• Do not use a damaged accessory; before each use
inspect the accessory such as abrasive wheels for
chips and cracks; after inspecting and installing an
accessory, position yourself and bystanders away
from the plane of the rotating accessory and run the
power tool at maximum no load speed for one
minute (damaged accessories will normally break apart
during this test time)
• The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool (accessories running faster than their rated speed
can fly apart)
• Never grind on the sides of a grinding wheel
(grinding on the side can cause the wheel to break and
fly apart)
• Use only grinding wheels with a minimum and a
maximum diameter of 200 mm
• Replace the grinding wheel, if it is worn down to Ø 150 mm
• Handle and store accessories with care
BEFORE USE
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
• Always mount spark guard A 2 and tool rest C 2; never
use the tool without them
• Before use, check that the grinding wheels are free of
damage, properly mounted, and able to rotate freely
• Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
DURING USE
• Wear protective gloves and use safety glasses
• The noise level when working can exceed 85 dB(A); wear
ear protection
• Anyone entering the work area must wear personal
protective equipment (fragments of the workpiece or of
a broken accessory may fly away and cause injury
beyond the immediate area of operation)
• When grinding metal, sparks are generated; keep other
persons and combustible material from work area
• Keep hands away from the rotating grinding wheels
• Do not brake the grinding wheels with side pressure
• Allow the tool to cool down after a continuous use of 30
minutes (S₂ 30 min.)
• If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
AFTER USE
• Lift or support the tool during transportation with both
hands holding protective covers G 2
EXPLANATION OF SYMBOLS ON TOOL
3 Read the instruction manual before use
4 Wear protective glasses
5 Double insulation (no earth wire required)
6 Do not dispose of the tool together with household waste
material
9