HID iCLASS SE RKLB40 Manual De Instrucciones página 3

iCLASS SE® Biometric Reader
2.2 Initial Setup – Site Key
Note: This stage applies only when the Template Type is set
to Seos.
The Site Key setup follows the Operational Mode setup.
The Site Key encrypts the biometric credentials onto the
card so they are unique to each site. The Site Key must be
between 6 and 11 characters and must be entered identically
onto all readers on that particular site.
To choose the Site Key:
1. Enter the Site Key and press #.
2. The reader will display Verify Key. Enter the Site Key
number again and press #.
Site Key
Enter PIN
******
Note: If the Site Key number is not entered within the
timeout period the Reader will display Enrollment Failed
and return to the Site Key menu.
3. Once the Site Key value has been successfully entered
and verified, the Reader displays Success! and
advances to the next stage.
2.3 Initial Setup – Verify Admin
The final stage of Initial Setup registers the Admin card. The
Reader presents two choices: Enroll Admin or Present Card
in order to verify an existing Admin card.
Verify Admin
1. Enroll Admin
2. Present card
Note: The following Enrollment dialog is the same for Initial
Setup, Add Admin, and Add User. The main title at the top of
the display changes to indicate the current function.
2.3.1 Enrollment Dialog
Example: "Enroll Admin" choice in the "Verify Admin" step
The Reader displays:
1. Enroll Admin
2. Present Card
Note: The user should chose 2. Present Card if they already
have an Admin card. When an Admin card is successfully
presented to the Reader (it will ask for a finger to be
presented and Local PIN Verify, if required) this choice will
succeed. If there is a failure to present an Admin card, then
an error message is shown and the Verify Admin menu is
re-presented.
1. Select 1. Enroll Admin. The Reader displays:
First Finger
Capture 1 of 3
Put finger on sensor
RKLB40
SRD MODEL: RKCLB40E
The Reader will request to capture the first finger three
times.
First Finger
Capture 1 of 3
Put finger on sensor
Note: The second line on the display will give instructions to
the user, such as Put finger on sensor, Press harder, Move
right, Remove finger, and so on. Also, for each of the three
captures it is recommended that the user fully removes their
finger and repositions it slightly differently on the sensor
(e.g., more pressure, to one side a little) as this allows the
sensor to collect more/different information.
The Reader then asks for the second finger to be captured
three times.
When the operation is complete the Reader displays
Success.
Note: If there is an error, if the fingerprint is not captured, or
if the Reader times out, the Reader displays Authentication
Failed and the sequence returns to the Enroll Admin screen.
After three failed attempts the display reverts to the main
menu. In the case of Initial Setup the display returns to the
Verify Admin menu, as you must successfully enroll a new
Admin (or prove that you have already done so) to exit that
step.
2. If a Local PIN Verify number is required, the Reader
then displays:
Keypad PIN
Enter the PIN number and press #. The PIN number can
be from 1 to 12 digits. You must the end entry with the
# key, unless you use a 12-digit PIN in which case the
Reader accepts the PIN when the 12th digit is entered
and the # key is not required.
The Reader will display Verify PIN. Enter the PIN again
and press #.
Note: If the PIN is not entered within the timeout
period the Reader will display Enrollment Failed and
will prompt the user to try again. After three attempts
the sequence returns to the Enroll Admin screen.
3. The Reader then displays:
Write to card
Present card
Present the card to the reader. If successful, the Reader
will reboot into the Operational Mode you have chosen
for it and is ready for normal use.
3
Enroll Admin
PLT-03342, Rev. A.3