HID iCLASS SE RKLB40 Manual De Instrucciones página 4

iCLASS SE® Biometric Reader
3. Operation – Reader
In Reader Mode, the display shows the Present Card screen.
iCLASS SE
Present Card
1. Present the card to the Reader.
2. Follow the on-screen prompts to present a finger to the
Reader, if required.
Note: To ensure a good quality fingerprint acquisition:
ƒ Do not press too hard
ƒ Do not move finger during acquisition
ƒ Leave your finger on the sensor at least 2 seconds
ƒ Do not slide or roll your finger across the sensor
3. Enter your Local PIN Verify number, if required.
Note: These requirements can be changed via the
Configuration menu.
4. When successful, the Reader will:
ƒ Beep and flash green (LED).
ƒ Display Success!
ƒ Transmit the access information that is stored on
the card to an attached panel.
Note: If the information provided does not match
what is stored on the presented card, the iCLASS SE
Biometric Reader will prompt the user to try again.
After four unsuccessful attempts at verification the
display reverts to Present Card and the user must start
over.
Note: If a card with no fingerprint template is
presented the reader will display "Security Error".
4. Operation – Administration
4.1 Access the Administration Menu
If the Reader is configured to be a Reader/Enroller and
the user wishes to access Administration mode, follow this
procedure:
1. The Reader that is configured to be a Reader/Enroller
displays the Present Card menu as its main screen.
2. Before you present a card, select 1 on the keypad.
3. Present an Admin card then remove the Admin card
from the reading field and follow the on-screen
prompts to verify biometric information and Local PIN
Verify number as required.
RKLB40
SRD MODEL: RKCLB40E
4.2 Administration Menu Functions
From the Administration menu, access the functions below.
Note: Each menu will return to the main menu if it times out
(time out occurs after 8 seconds).
1. Manage Users
2. Manage Admins
3. Configuration
4. < exit >
4.2.1 Manage Users
This presents the choice of enrolling or verifying a User:
the standard Enrollment dialog is used (see Section 2.3.1:
Enrollment Dialog).
4.2.2 Manage Admins
This presents the choice of enrolling an Admin or verifying
an existing Admin card. Each option follows the standard
Enrollment dialog (see Section 2.3.1: Enrollment Dialog). The
other choice is to revoke an Admin. If this option is chosen
the user must present an existing Admin card to the reader.
Users need to ensure they always have at least one Admin
card on the site as the only way to get a replacement Admin
card is to reset the reader to the factory setup and go
through the initial setup process.
4.2.3 Configuration Menu Functions
To access the Configuration menu, select 3 from the
Administration menu.
Note: The options in the Configuration menu will differ,
depending on how the Reader has been set up. For example,
If the Reader has been set up for iCLASS or iCLASS SR
cards, then non-relevant menus (e.g., Site Key) will not be
displayed.
1. Language
2. Credential type
3. Mode
4. < more >
Language: Changes the language.
1.
2. Template Type: Changes the Template Type.
Notes:
ƒ If the user changes the Template Type from iCLASS
cards to Seos cards, then the user must exit the
Administration menu before enrolling Seos User or
Admin credentials. After exiting the administration
menu the reader will prompt the user to enter a
Site Key for reader Seos operation. The Site Key
can then be set and an Admin card created which
matches the Site Key of the reader. Note: If the
Template Type is changed in this way, all readers on
a site must be reconfigured with the same Site Key.
ƒ If the user changes the Template Type from
Seos cards to iCLASS cards, then the Reader will
reboot into Initial Setup – Verify Admin mode. The
confirmation Yes/No dialog will display (because
the Site Key is not required for iCLASS or iCLASS
SR cards).
4
Administration
Configuration
PLT-03342, Rev. A.3