Hitachi AXF100E Guía De Operación página 97

Tabla de contenido

Publicidad

• TROUBLESHOOTING
Check the following before assuming there is a problem with the system.
1. Are connections properly made?
2. Is the system being operated as explained in the operating instructions?
If the system does not seem to be operating properly, check as shown on the table below.
If none of these checks apply to the problem, the system may be malfunctioning.
Disconnect the power cord immediately and contact the store from which this unit was purchased.
Symptom
Unit does not turn on
when power operation
switch is pressed.
No sound is produced
from the speakers.
No treble sound is
produced, or the position of
the instruments is unclear.
A source other than the
desired one is heard.
Hissing sound is heard in
FM programs.
Hissing sound is heard in
MW programs.
Humming sound is heard
in MW programs.
Total numbers of tracks
not displayed when disc is
loaded.
Nothing happens when
operating buttons are
pressed.
Disc stops in the middle of a
track and will not play properly.
Sound is broken.
Humming sound is heard
when disc is played.
Protector circuit
• The HCU-R30E is equipped with a high speed protector circuit.
This circuit protects internal parts from being damaged by strong currents generated in the unit should the unit be
operated when the speaker terminals are incompletely connected or short circuited.
If this protector circuit is activated, a relay sound is produced, the output to the speakers is interrupted, and the
indicator blinks rapidly to indicate that there is a problem. If this should happen, unplug the power cord, and contact
your store of purchase.
• The unit may not operate properly due to such external influences such as lightning or static electricity. If this
happens, either turn off the power with the power operation switch or unplug the power cord, wait approximately 5
seconds, then plug the power cord back in.
All manuals and user guides at all-guides.com
Cause
• Power cord is not plugged into a power
outlet.
• VOLUME control is turned down.
• Headphones are connected.
• Speaker cords are not securely
connected.
• Muting is on.
• Speaker polarities (Œ and œ) are
inverted.
• Function is not properly set.
• Antenna direction is poor.
• Signals from the broadcast station are
weak.
• Noise from a TV or interference from a
broadcast station.
• Signals on the power cord are being
modulated by the power source
frequency.
• Disc is loaded upside-down.
• Disc is dirty.
• Disc is not of the specified type.
• Disc is loaded upside-down.
• Foreign object on disc tray.
• Disc is dirty.
• Disc is scratched.
• Dirt, fingerprint, spittle, etc, on disc.
• Disc is scratched.
• Player is in an unstable place or a
place that vibrates strongly.
• Signals on the power cord are being
modulated by the power source
frequency.
97
Countermeasure
• Plug the power cord securely into an
outlet.
• Set the control to an
appropriate position.
• Disconnect the headphones.
• Connect securely.
• Turn off Muting.
• Connect the speaker cords properly.
• Set the desired function using the
FUNCTION button.
• Change the direction of the antenna.
• Install an outdoor antenna.
• Turn the TV off.
• Change the direction of the loop antenna.
• Install an outdoor antenna.
• Insert the power cord in the opposite
direction.
• Install an outdoor antenna.
• Reload the disc.
• Clean the disc.
• Replace with a disc of the specified
type.
• Reload the disc.
• Remove the disc and the foreign
object.
• Clean the disc.
• Replace with an unscratched disc.
• Clean the disc.
• Replace with an unscratched disc.
• Place the player in a stable place
with no vibrations.
• Insert the power cord in the opposite
direction.
English

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Axf100ebsAxf100ucAxf100wAxf100wun

Tabla de contenido