KEB COMBIVERT F0 V1.2 Manual De Instrucciones página 126

Annex B - Parameter Summary F0
Operation Parameter
Page 41-44
o.0 : boost
1)
o.1 : minimum reference A
1)
o.2 : maximum reference A
1)
o.6 : acceleration time A
1)
o.8 : deceleration time A
1)
o.13 : input source
1) 2)
o.14 : Delta - Boost
1)
o.15 : Delta - Boost time
1)
o.16 : s-curve acceleration time A
1)
o.17 : s-curve deceleration time A 1)
Parameters for Standard Applications!
1) Parameters that can be changed in parameter
sets 1 to 6!
2) Parameter value is stored only after pressing "EN-
TER" twice!
RUN Parameter
Page 37-40
r.0 : prom no.
r.1 : inverter status
r.2 : actual value display
r.3 : set value display
r.4 : output voltage
r.5 : DC voltage
r.6 : DC circuit peak voltage
r.7 : current inverter utilization
r.8 : peak load
Protection Parameter
Page 45-50
P.0 : stall prevention level
1)
P.1 : acc / dec time during stall prevention
1)
P.2 : stall torque characteristic
1) 2)
P.3 : LAD stop load level
1)
P.4 : U/f - function
1)
P.6 : speed search condition
1)
P.7 : automatic retry UP
1)
P.11 : energy - saving mode
1) 2)
P.12 : energy - saving level
1)
P.13 : LAD stop condition 1)
P.14 : LD stop DC voltage level 1)
P.15 : load-dependent set shifting level 1)
Drive Parameter
Page 57-61
d.0 : rated frequency
1)
d.1 : f-mode
1)
d.2 : lower modulation limit
1)
d.4 : rated motor power
1)
d.18 : slip compensation / frequency gain
1)
d.19 : slip compensation / auto torque gain
1)
d.20 : slip compensation / min. frequency
1)
d.21 : slip compensation / max. frequency
1)
d.22 : slip compensation / no-load losses
1)
d.23 : slip comp./load-no-load differ.display
d.24 : number of pole pairs 1)
Customer Parameter
Page 62-70
C.0 : limit of maximum reference A 1)
C.2 : rotation lock 1) 2)
C.4 : condition display
C.5 : noise fi lter / digital inputs
C.6 : DC level auto set 1)
C.7 : DC-braking mode 1) 2)
C.8 : carrier frequency
1)
C.9 : parameter group lock
C.10 : output voltage stabilization
1) 2)
C.12 : baud rate
C.13 : inverter address
C.14 : zero clamp speed
1)
C.15 : select mode of modulation
1) 2)
C.21 : watchdog time
C.25 : control word activation
C.27 : application selection
r.14 : input terminal status
r.15 : output terminal status
r.18 : bus address display
r.19 : reference setting 1)
r.20 : rotation setting 1) 2)
r.21 : password input
r.22 : select parameter group
r.23 : select parameter set
r.29 : current frequency
Input / Output Handler
Page 51-53
H.0 : presetting mode reference value
1) 2)
H.1 : logic of analog inputs
1) 2)
H.3 : output logic
1) 2)
H.4 : Out 1 - function
1) 2)
H.5 : Out 2 - function
1) 2)
H.7 : input logic
2)
H.8 : In -function parameter set
2)
H.9 : analog output function
1) 2)
H.10 : analog output offset y 1)
H.11 : analog output gain 1)
Free-programmable Parameter Sets
Page 71-74
F.0 : key parameter set no.
F.3 : based on para set
F.4 : global enter
F.5 : clear top parameter set
F.6 : bus parameter set no.
F.7 : save last bus parameter
Information Parameter
Page 75-76
I.0 : inverter type
I.1 : rated inverter current display
I.2 : output frequency limit display
I.3 : error counter OP
I.4 : error counter UP
I.5 : error counter OC
I.6 : error counter OH
I.7 : error counter OL
I.8 : error counter set selection
I.9 : error counter watchdog
Level Parameter
Page 54-56
L.0 : actual value level 1
1)
L.1 : actual value level 2
1)
L.2 : load level 1
1)
L.3 : load level 2
1)
L.6 : DC dynamic braking level
1)
L.7 : DC dynamic braking voltage
1)
L.8 : DC dynamic braking time
1)
L.16 : timer value
1)
L.17 : timer adding value 1)
Profi l Parameter
Page 77-79
Pr.5 : malfunction code
Pr.6 : control word
Pr.7 : status word
Pr.8 : nominal speed value
Pr.9 : actual speed value
Pr.10 : speed-min-amount
Pr.11 : speed-max-amount
Pr.16 : acceleration-delta speed
Pr.18 : acceleration-delta time
Pr.25 : deceleration-delta speed
Pr.27 : deceleration-delta time
Pr.37 : speed reference value