Lutron RadioRA 2 Pico RRD-P3BRL-L Manual De Instrucciones

Wall Mount Template
Please Read Before Installing
The Pico wireless control can be mounted to a wall in three ways. Choose the
appropriate template and installation procedure listed below for your application.
A—No Wallplate Template
B—Single Gang Template
C—Multiple Gang Template
A
No Wallplate Template
LUTRON
1. Carefully cut out the template below along the dashed line and temporarily at-
tach it to the wall at the desired mounting location.
2. Mark and drill the 3/16 in (5 mm) screw hole locations indicated within the Wall
Mount Plate on the template.
3. Remove template and insert one Screw Anchor into each of the holes drilled in
step 2, making sure they are flush with the wall.
4. Loosely mount the Wall Mount Plate to the wall with the Mounting Screws.
Check to make sure the Wall Mount Plate is level. Once the Wall Mount Plate is
level, tighten the screws.
5. Slide the Pico control down onto the Wall Mount Plate.
LUTRON
3/16 in (5 mm) Drill
(not included)
Wall Mount
Screw Anchor
Plate
Mounting Screw
PRINTING INSTRUCTIONS:
Lutron Elec tron ics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
Made and print ed in the U.S.A. 05/10 P/N 044-166 Rev. B
C
Multiple Gang Template
Cut out to provide
existing control
3/16 in (5 mm) Drill
(not included)
Screw Anchor
Mounting Screw
As Applicable
PRINTING INSTRUCTIONS:
English
1. Carefully cut out the template below along the dashed line
Pico wireless control
TM
RRD-P3BRL-L, RRD-P3BRL-S
2. Mark and drill the 3/16 in (5 mm) screw hole locations
3. Remove template and insert one Screw Anchor into each of
2.7 in (68.6 mm)
when printed to
correct size
Lutron, RadioRA, and the sunburst logo are registered trademarks and Pico and RadioRA 2 are trademarks of Lutron Electronics Co., Inc.
©2010 Lutron Electronics Co., Inc.
1. Carefully cut out the template below along the dashed line that represents
the appropriate multiple gang application. Cut along the solid line to provide
clearance for any existing controls. Temporarily attach the template to the
wall at the desired mounting location.
2. Mark and drill only the 3/16 in (5 mm) screw hole locations, indicated within
the Wall Mount Plate(s) and Wallplate Adapter on the template, that will
have a Pico control installed.
3. Remove the template and insert one Screw Anchor into each of the holes
drilled in step 2, making sure they are flush with the wall.
Cut out to provide
clearance for clearance for
existing control
Wall Mount
Wall Mount Wall Mount
Plate
B
Single Gang Template
LUTRON
and temporarily attach it to the wall at the desired mounting
location.
indicated within the Wall Mount Plate and Wallplate Adapter
on the template.
the holes drilled in step 2, making sure they are flush with the
wall.
3/16 in (5 mm) Drill
(not included)
Screw Anchor
Mounting Screw
PAGE SIZE: 8.5 X 11 PAGE SCALING: NONE
4. Loosely mount the Wall Mount Plate to the wall with the Mounting Screws.
5. Slide the Pico control down onto the Wall Mount Plate.
6. Mount the Wallplate Adapter with the mounting screws provided with the
Cut out to provide
clearance for
existing control
Wall Mount
Plate
Plate Plate
2-Gang Wallplate Adapter
(CW-2-XX)
PAGE SIZE: 8.5 X 11 PAGE SCALING: NONE
4. Loosely mount the Wall Mount Plate to the wall with the
Mounting Screws. Check to make sure the Wall Mount Plate
is level. Once the Wall Mount Plate is level, tighten the screws.
5. Slide the Pico control down onto the Wall Mount Plate.
LUTRON
6. Mount the Wallplate Adapter with the mounting screws
provided with the Pico control and snap the Wallplate onto the
Wallplate Adapter. DO NOT use the screws that came with the
Wallplate Adapter.
Wall Mount
Plate
1-Gang Wallplate Adapter
(CW-1-XX)
Check to make sure the Wall Mount Plate is level. Once the Wall Mount
Plate is level, tighten the screws.
LUTRON
Pico control and snap the Wallplate onto the Wallplate Adapter. DO NOT
use the screws that came with the Wallplate Adapter with openings where a
Pico control will be installed.
Cut out to provide
clearance for
existing control
Wall Mount
Plate
3-Gang Wallplate Adapter 4-Gang Wallplate Adapter
(CW-3-XX)
4.7 in (119.4 mm)
when printed to
correct size
4.7 in
(119.4 mm)
when printed
to correct size
(CW-4-XX)