Stanley FATMAX SFMCS701 Manual Del Usuario página 17

Note: Place the clamp on the opposite side of the base when
bevelling. ALWAYS MAKE DRY RUNS (UN-POWERED) BE-
FORE FINISH CUTS TO CHECK THE PATH OF THE BLADE.
ENSURE THE CLAMP DOES NOT INTERFERE WITH THE
ACTION OF THE SAW OR GUARDS.
Adjustments
Your mitre saw is fully and accurately adjusted at the factory at
the time of manufacture. If readjustment due to shipping and
handling or any other reason is required, follow the instruc-
tions below to adjust your saw.
Once made, these adjustments should remain accurate. Take
a little time now to follow these directions carefully to maintain
the accuracy of which your saw is capable.
Mitre scale adjustment (fig. Q1)
Lock the arm in the down position. Unlock the mitre lock
knob (5) and swing the mitre arm until the mitre latch button
(6) locks it at the 0° mitre position. Do not lock the mitre lock
knob. Place a square against the saw's fence and blade,
as shown. (Do not touch the tips of the blade teeth with the
square. To do so will cause an inaccurate measurement.) If
the saw blade is not exactly perpendicular to the fence, loosen
and move the material fence until the blade is perpendicular
to the fence, as measured with the square. Pay no attention to
the reading of the mitre pointer at this time.
Bevel square to table adjustment (Fig. Q2)
To align the blade square to the table, lock the arm in the
down position with the lock down pin (20). Place a square
against the blade, ensuring the square is not on top of a tooth.
Loosen the bevel lock knob (5) and ensure the arm is firmly
against the 0° bevel stop. Rotate the 0° bevel adjustment
screw with the 1/2" (12.7 mm) socket (not provided) as neces-
sary so that the blade is at 0° bevel to the table, as measured
with the square.
Guard actuation and visibility (Fig. V)
Warning! Pinch hazard. To reduce the risk of injury, keep
thumb underneath the operating handle when pulling the
handle down. The lower guard will move up as the operating
handle is pulled down, which could cause pinching.
The lower guard (4) on your saw has been designed to au-
tomatically uncover the blade when the arm is brought down
and to cover the blade when the arm is raised.
Before each use or after making adjustments, cycle the arm
(un-powered) and make sure the guard opens smoothly and
closes fully. It should not contact the blade. With the arm
up, raise the guard (un-powered) as shown in Figure V and
release. The guard should fully close rapidly.
Do not operate the saw if the guard does not move freely and
fully close rapidly. Never clamp or tie the guard in an open
position when operating the saw.
(Original instructions)
The guard can be raised by hand when installing or removing
saw blades or for inspection of the saw.
NEVER RAISE THE LOWER GUARD MANUALLY UNLESS
THE BLADE IS STOPPED.
Note: Certain special cuts of large material will require that
you manually raise the guard. Refer to cutting large material
under special cuts.
The front section of the guard is louvred for visibility while
cutting. Although the louvres dramatically reduce flying debris,
they are openings in the guard and safety glasses should
be worn at all times.
Rail Guide
Periodically check the rails (13) for any play or clearance. The
rails can be cleaned with a dry clean cloth.
Cutting Picture Frames, Shadow Boxes And Other
Four-Sided Projects (Fig. R1, R2)
To best understand how to make the items listed here, we
suggest that you try a few simple projects using scrap wood
until you develop a "feel" for your saw.
Your saw is the perfect tool for mitreing corners like the one
shown in Figure R1. Sketch A in Figure R2 shows a joint made
by using the bevel adjustment to bevel the edges of the two
boards at 45º each to produce a 90º corner. For this joint the
mitre arm was locked in the zero position and the bevel ad-
justment was locked at 45º. The wood was positioned with the
broad flat side against the table and the narrow edge against
the fence. The cut could also be made by mitreing right and
left with the broad surface against the fence.
Cutting trim moulding and other frames (fig. R2)
Sketch B in Figure R2 shows a joint made by setting the mitre
arm at 45º to mitre the two boards to form a 90º corner. To
make this type of joint, set the bevel adjustment to zero and
the mitre arm to 45º. Once again, position the wood with the
broad flat side on the table and the narrow edge against the
fence.
Figures R1 and R2 are for four-sided objects only.
As the number of sides changes, so do the mitre and bevel
angles. The chart below gives the proper angles for a variety
of shapes.
Examples
Number of Sides
4
5
6
7
8
ENGLISH
Mitre or Bevel Angle
45°
36°
30°
25.7°
22.5°
17