Warranty /Procedure In Case Of Repair; Product Specifications - Ivoclar Vivadent Bluephase Style 20i Instrucciones De Uso

7. Warranty / Procedure
in Case of Repair
The warranty period for Bluephase Style 20i is 3 years
from the date of purchase (battery: 1 year). Malfunctions
resulting from faulty material or manufacturing errors
are repaired free of charge during the warranty period.
The warranty does not provide the right to recover any
material or non-material damage other than the ones
mentioned. The apparatus must only be used for the
intended purposes. Any other uses are contraindicated.
The manufacturer does not accept any liability resulting
from misuse and warranty claims cannot be accepted in
such cases. This is particularly valid for:
• Damage resulting from improper handling, especially
incorrectly stored batteries (see Product Specifi-
cations: Transportation and storage conditions).
• Damage to components resulting from wear under
standard operating conditions (e.g. battery).
• Damage resulting from external influences, e.g. blows,
drop to the floor.
• Damage resulting from incorrect set-up or installation.
• Damage resulting from connecting the unit to a
power supply, the voltage and frequency of which do
not comply with the ones stated on the rating plate.
• Damage resulting from improper repairs or
modifications that have not been carried out by
certified Service Centres.
In case of a claim under warranty, the complete
apparatus (handpiece, charging base, power cord and
power pack) must be returned, carriage paid, to the
dealer or directly to Ivoclar Vivadent, together with the
purchase document. Use the original packaging with
the corresponding cardboard inserts for transportation.
Repair work may only be carried out by a certified
Ivoclar Vivadent Service Centre. In case of a defect that
cannot be rectified, please contact your dealer or your
local Service Centre (see addresses on the reverse side).
A clear description of the defect or the conditions under
which the defect occurred will facilitate locating the
problem. Please enclose this description when returning
the apparatus.

8. Product Specifications

Light source Ivoclar Vivadent Polywave® LED
Wavelength range 385–515 nm
Light intensity TURBO program:
2,000 mW/cm2 ± 10 %
HIGH POWER program:
1,200 mW/cm2 ± 10 %
Operation 3 min on / 7 min off (intermittent)
Light probe 10>8 mm black, auto clavable
Anti-glare cones auto clavable
Signal transmitter acoustic signal after 5 or every 10 seconds
and every time the start button or the
time/ program selection button is pressed
Dimensions of the L = 180 mm, B = 30 mm, H = 30 mm
handpiece (without
light probe)
Weight of the 120 g (including battery and light probe)
handpiece
Operating voltage 3.7 VDC with battery
handpiece 5 VDC with power pack
Operating voltage 5 VDC
Charging Base
Power supply Input:
100–240 VAC, 50 –60 Hz 310 mA
Output:
5 VDC / 2 A
Manufacturer Friwo
Type: FW7401M/05
Operating conditions Temperature +10 °C to +30 °C
(+ 50 °F to + 86 °F)
Relative humidity 30% to 75%
Ambient pressure 700 hPa to 1060 hPa
Dimensions of the D = 125 mm, H = 70 mm
charging base
Weight of the 195 g
charging base
Charging time Approx. 2 hours (with the battery empty)
Power supply of the Li-Po battery
(approx. 20 min. with a new, fully charged
handpiece
battery in the High Power program)
Transportation and Temperature –20 °C to +60 °C
storage conditions (+4 °F to +140 °F)
Relative humidity 10% to 75%
Ambient pressure 500 hPa to 1060 hPa
The curing light has to be stored in
closed, roofed rooms and must not be
exposed to severe jarring.
Battery:
– Do not store at temperatures above
– Keep the battery charged and store no
Delivery form 1 Charging base with power cord and
power pack
1 Handpiece
1 Light probe 10>8 mm, black
1 Anti-glare shield
3 Anti-glare cones
1 Pack of sleeves (1 x 50 pcs.)
1 Instructions for Use
40 °C / 104 °F (or 60 °C / 140 °F for a
short period). Recommended storage
temperature 15–30 °C (59–86 °F).
longer than 6 months.
19