Publicidad
Idiomas disponibles
Idiomas disponibles
Personalisation of display initial text
(code 04)
You can modify the text shown on the
display during normal operation or idle
state. You must program bit 4 or bit 5 to
display
the
text
(see
programming").
To insert the personalized text, you must:
Move the jumper J1 from 1-2 to 2-3.
Enter the code 04 and press
display shows "DF6000 system /
TD6100MA", in case of first program-
ming, or the text you want to replace.
For information on how to enter the char-
acters see "entry of names".
Press
to confirm; the display shows
"Programming / type: ".
Continue by entering the code of a new
programming or exit by moving the
jumper J1 back to 1-2.
Loading user-names from PC (code
05)
You can load names directly from
your PC.
Load the user-names on the PC using
the Farfisa software application
(supplied on demand).
Turn OFF the push-button panel and
the PC.
Connect the PC serial port to the stereo
jack on the back of the push-button
panel with a cable as shown in the figure
below.
PC serial port
1
6
2
7
3
8
4
9
5
to PC
TD6100MAS
Move the jumpers J1, J2 and J3 on the
back of the push-button panel from 1-2
to 2-3.
Turn on the PC and then the push-
button panel.
Enter the code 05; the display shows
"TD6100MA > PC / in progress 0".
Download the names from the PC
within 15 seconds; the display shows
"system
"TD6100MA < —> PC / in progress
1", "TD6100MA <—> PC / in
progress 2" and then the downloaded
names.
; the
At the end of download the push-
button deletes the existing names.
The first line of the display shows
"waiting" and the second line shows
a status bar to show the progress of
the deletion operation. At the end
the display shows "Programming /
type: ".
Turn off the push-button panel and
then the PC.
Disconnect the cable from the PC
and the push-button panel.
Bring the jumpers J1, J2 and J3
back to 1-2.
Ordering names (code 06)
You can list the names in alphabetical
order (from A to Z).
Move the jumper J1 from 1-2 to 2-3.
Enter the code 06; the first line of the
display shows "waiting" and the sec-
ond line shows a status bar; at the
end of the operation the push-but-
Stereo jack
ton panel returns automatically to
Ø = 2,5mm
the programming mode (the dis-
play shows "Programming / type:" ).
3
Exit the programming mode by
2
bringing the jumper J1 back to 1-2.
5
Door lock activation time (code 10)
5
To change the time of release the
2
door lock, you must:
3
move the jumper J1 from 1-2 to 2-3;
enter code 10 and press the button
; the display shows "TIME S1";
dial the number corresponding to
the desired timing seconds to acti-
vate the door lock (from 1 to 60);
press the button
exit the programming mode by
bringing the jumper J1 back to 1-2.
Inserting the button address P1
(code 11)
To save an extension number and call
it directly from a button connected
between terminals "P1" and "-":
move the jumper J1 from 1-2 to 2-3;
enter the code 11 and press the
button
DRESS P1";
dial the extension number. Exten-
sions must be coded with numbers
from 1 to 255;
press the button
exit the programming mode by
bringing the jumper J1 back to 1-2.
Choice the calling tone (code 12)
To change the calling tone, you must:
move the jumper J1 from 1-2 to 2-3;
enter code 12 and press the button
; the display shows "MELODY";
dial the number corresponding to
the preferred calling tone (from 00 to
03 - see table of the calling tones on
page 14);
press the button
exit the programming mode by
bringing the jumper J1 back to 1-2.
Reset default programming (code
90-91-92)
To return the keypad to program the
factory and then delete all changes
made during programming, you must:
move the jumper J1 from 1-2 to 2-3.
enter code 90, 91 or 92 and press
the button
spectively "DEFAULT SETTINGS /
YES < > NO"; "ERASE PASS-
WORDS / YES < > NO"; "ERASE
USERS / YES < > NO". Press
execute the operation or
parameters unchanged;
exit the programming mode by
bringing the jumper J1 back to 1-2.
Return to operation mode
Once you have completed program-
to confirm;
ming, bring the jumper J1 back to 1-2;
the display shows "ACI FARFISA /
press < >" or the text you have entered
during
"Personalization of display initial
text").
; the display shows "AD-
to confirm;
to confirm;
; the display shows re-
to
to leave
programming
(see
13
Mi 2437/1
Publicidad
