Hoshizaki KM-100A Manual De Instrucciones página 6

Control Box
Fig. 5
2. PREPARING THE ICEMAKER FOR LONG STORAGE
IMPORTANT
When shutting off the icemaker for an extended time, drain out all
water from the water lines and remove the ice from the storage bin.
The storage bin should be cleaned and dried. Drain the icemaker
using air or carbon dioxide to prevent damage to the water supply
lines at sub-freezing temperatures. Shut off the icemaker until the
proper ambient temperature is resumed.
When the icemaker is not used for two or three days, it is sufficient to
only move the control switch to the "OFF" position, unless the icemaker
will be at sub-freezing temperatures.
[1] Remove the water from the potable water supply line:
1) Remove the louver if it has not already been removed.
2) Move the control switch on the control box to the "OFF" position. See
Fig. 5.
3) Wait 3 minutes.
4) Close the potable water supply line stop valve. See Fig. 4.
5) Remove the inlet hose.
[2] Drain the potable water tank:
1) Move the control switch to the "SERVICE" position and the service
switch to the "DRAIN" position.
2) After 2 minutes, move the control switch to the "OFF" position.
3) Open the door. Remove all ice from the storage bin and clean the
storage bin.
4) Close the door.
5) Replace the louver in its correct position.
6) Turn off the power supply at the breaker box.
All manuals and user guides at all-guides.com
III. MAINTENANCE
1. CLEANING
[1] Exterior
Control Switch
Wipe the exterior at least once per week with a clean, soft cloth. Use a
Service Switch
damp cloth containing a neutral cleaner to wipe off grease or dirt.
[2] Scoop and Bin Door Grip Cleaning/Sanitisation (Daily)
1) Either mix 3 litres of water with 11 ml of 5.25% sodium hypochlorite
2) Soak the scoop in the solution for more than 3 minutes. Rinse
3) Use a neutral cleaner to wash the bin door grip. Rinse thoroughly.
4) Soak a clean cloth with the sanitising solution, and wipe the grip. Use
[3] Storage Bin Interior Cleaning/Sanitisation (Weekly)
1) Open the storage bin door, and remove all ice.
2) Wash the bin liner with a neutral non-abrasive cleaner. Rinse
3) Soak a clean cloth with the neutral cleaner, and wipe the door inner
4) Either mix 3 litres of water with 11 ml of 5.25% sodium hypochlorite
5) Soak a clean sponge or cloth with the solution, and wipe the bin liner
6) Rinse thoroughly with fresh water and a clean cloth to wipe off the
[4] Air Filter
Plastic mesh air filters remove dirt or dust from the air, and keep the
condenser from getting clogged. If the filters get clogged, the icemaker's
performance will be reduced. Remove and clean the air filters at least
twice per month:
1) Tilt the louver forward, and remove the air filter.
2) Clean the air filter by using a vacuum cleaner. When severely clogged,
3) Rinse and dry the air filter thoroughly, and place it in position.
5
WARNING
1. Before carrying out any cleaning or maintenance operations,
unplug the icemaker from the electrical supply network.
2. Ask a trained service person to check and clean the condenser
at least once a year.
3. This appliance must not be cleaned by use of a water jet.
4. Do not use any alcohol for cleaning/sanitisation of the icemaker.
It may cause cracks on the plastic parts.
5. To prevent possible damage, do not clean the plastic parts
with water above 40°C or in a dishwasher.
solution in a suitable container, or the recommended Hoshizaki
sanitiser as directed.
thoroughly, and shake to remove surplus liquid.
Note: Using a cloth to dry may re-contaminate.
fresh water and a clean cloth to rinse/dry.
thoroughly.
surface. Wipe off the cleaner with a clean damp cloth.
solution in a suitable container or the recommended Hoshizaki
sanitiser as directed.
and bin door.
solution. Close the bin door.
Note: Some solutions may cause damage to the bin liner surfaces or
corrosion on the metal parts. Always rinse the sanitiser unless
directed otherwise by Hoshizaki guidelines.
use warm water and a neutral cleaner to wash the air filter.
ENGLISH