Before Starting The Equipment - EINHELL TE-MG 200 CE Manual De Instrucciones

The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect con-
ditions.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1 Fitting the plug-in tools (Figures 1/2/3)
•
To fit the plug-in tools safely you should hold
the multifunction tool so that the ON/OFF
switch (1) points down and the tool mounting
(2) faces up.
•
Place the plug-in tool (e.g. the triangular san-
ding/grinding plant) on the tool mounting (2)
so that the pins of the tool mounting (2) fit into
the recesses in the plug-in tool.
•
Secure the plug-in tool using the supplied
Anl_SA_TE_MG_200_CE_SPK8.indb 27 Anl_SA_TE_MG_200_CE_SPK8.indb 27
GB
screw (b) and tighten the screw securely with
the Hexagon key (9).
•
Make sure that the washer (a) is used for the
screw (b) only in connection with the saw
blade and the scraper (see Figure 3). In this
case the corrugated face of the washer must
be placed against the plug-in tool.
Check that the plug-in tool is secure.
5.2 Triangular sanding/grinding plate
Fit the triangular sanding/grinding plate to use the
equipment as a delta sander/grinder.
5.2.1 Fastening the sanding/grinding paper
The Velcro fastener enables easy changing of
sanding/grinding paper. Make sure that the va-
cuum extraction holes on the sanding/grinding
paper and the sanding/grinding disk are aligned.
5.3 Fitting the dust extraction device
(Fig. 4/5)
The dust extraction system prevents the accumu-
lation of dirt and high dust loads in the air, and it
makes it easier to dispose of the dust.
•
Place the equipment in a stable position as
shown in 5.1.
•
Fit the dust extraction device (6) with the tool
mounting (2) positioned as shown in Figure 4.
•
Fasten the dust extraction device (6) by lat-
ching it in the air vents.
•
Connect the extractor adapter (3) to the dust
extraction device (6). Make sure that the ar-
row (a) on the extractor device coincides with
the recess (b) on the dust extraction device
(6) (see Fig. 5). Turn the extractor adapter (3)
anti-clockwise until it engages..
•
Connect your tool to an extraction unit or va-
cuum cleaner. This will provide excellent ext-
raction of chips and dust from the workpiece.
The benefi ts are that you will protect both the
equipment and your own health. Your work area
will also be clean and safe.
- 27 -
05.09.2018 07:59:36 05.09.2018 07:59:36