Sauder 109872 Manual De Instrucciones
  1. Manuales
  2. Marcas
  3. Sauder Manuales
  4. Muebles de Interior
  5. 109872
  6. Manual de instrucciones
Sauder 109872 Manual De Instrucciones

Sauder 109872 Manual De Instrucciones

Ocultar thumbs Ver también para 109872:
Tabla de contenido

Publicidad

Enlaces rápidos

Descargar este manual
sauder.com
72" U-Shaped Connector Kit
Heritage Hill Collection | 109872
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
We're in your corner.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-30
Français pg 31-34
Español pg 35-38
Lot # 375994
08/25/15
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987

Publicidad

Tabla de contenido
loading

Manuales relacionados para Sauder 109872

Resumen de contenidos para Sauder 109872

  • Página 1 Heritage Hill Collection | 109872 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Prefer the phone? Call 1-800-523-3987.

  • Página 2: Tabla De Contenido

    Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 5-30 Hammer Not actual size Français 31-34 Español 35-38 Skip the power trip. Warranty This time. Page 2 109872 www.sauder.com/services...

  • Página 3: Part Identifi Cation

    MODESTY PANEL (1) SHORT MOLDING (1) INNER END (1) SHELF (1) END MOLDING (2) RIGHT UPRIGHT (1) BOTTOM (1) LONG SKIRT (2) LEFT UPRIGHT (1) RIGHT MOLDING (1) SHORT SKIRT (2) E2 TOP (1) LEFT MOLDING (1) www.sauder.com/services 109872 Page 3...

  • Página 4: Hardware Identifi Cation

    HOLE PLUG - 3 BLACK 1-7/8" FLAT HEAD SCREW - 10 BROWN 1-1/2" FLAT HEAD SCREW - 3 BLACK 9/16" LARGE HEAD SCREW - 24 BLACK 9/16" WAFER HEAD SCREW - 2 SILVER 1-1/8" FLAT HEAD SCREW - 16 Page 4 109872 www.sauder.com/services...

  • Página 5: Important

    NOTE: You must assemble the 109843 Executive Desk fi rst, then the 109848 Return Kit before assembling this unit å (109872 U-Shape Connector Kit). NOTE: The diagram shows the 109848 Return Kit attached to the right side of the 109843 Executive Desk. Your 109848 å...
  • Página 6 IMPORTANT: Do not overtighten the SCREWS into the TOP. å SILVER 1-1/8" FLAT HEAD SCREW (14 used in this step) Do not overtighten Angled end the SCREWS (CC). When fastened, the MOLDINGS set in from the edges of the TOP. Large hole Page 6 109872 www.sauder.com/services...
  • Página 7 IMPORTANT: Do not insert TWIST-LOCK® FASTENERS å into the INNER END (B) in this step. Push a SAUDER TWIST-LOCK® FASTENER (T) into each å large hole in the OUTER END (A). Repeat this step for the RIGHT UPRIGHT (C), LEFT å...
  • Página 8 Step 4 Fasten the OUTER END (A) to the SHORT MOLDING (K). å ® How to use the SAUDER TWIST-LOCK FASTENER Tighten two TWIST-LOCK® FASTENERS. 1. Insert the dowel end of the FASTENER into the hole of the adjoining part.
  • Página 9 Use two BLACK 9/16" LARGE HEAD SCREWS (BB). NOTE: Be sure the edges of the BRACKETS are even with å the edges of the LONG SKIRTS. BLACK 9/16" LARGE HEAD SCREW (2 used in this step) www.sauder.com/services 109872 Page 9...
  • Página 10 SCREWS a few turns before tightening either of them. Next, fasten the METAL BRACKETS (U) on the LONG SKIRTS (M) to å the BOTTOM (H). Use two BLACK 9/16" LARGE HEAD SCREWS (BB) BLACK 9/16" LARGE HEAD SCREW (2 used for the METAL BRACKETS) Page 10 109872 www.sauder.com/services...
  • Página 11 Fasten the SHELF (G) to the MODESTY PANEL (F). å Tighten two TWIST-LOCK® FASTENERS. S u r Notch f a c i t h I S T - L O ® F A S T E N E R www.sauder.com/services 109872 Page 11...
  • Página 12 ® f a c S u r - L O I S T E R S T E N F A S BLACK 9/16" LARGE HEAD SCREW (4 used for the CORD MANAGERS) Page 12 109872 www.sauder.com/services...
  • Página 13 Step 9 You have the choice of assembling this unit two ways: å If attaching the 109872 U-Shape Connector Kit to the right å side of the 109843 Executive Desk, continue with step 10. If attaching the 109872 U-Shape Connector Kit to the left å...
  • Página 14 NOTE: Notice the location of the two holes in the middle å of the INNER END (B). Push a SAUDER TWIST-LOCK® FASTENER (T) into the å indicated large holes shown in the INNER END (B). NOTE: Do not push TWIST-LOCK® FASTENERS into the å...
  • Página 15 Fasten the INNER END (B) to the MOLDINGS (I and J). å Tighten two TWIST-LOCK® FASTENERS. S u r f a c i t h I S T - L O F A S T E N ® E R S www.sauder.com/services 109872 Page 15...
  • Página 16 Fasten the INNER END (B) to the MODESTY PANEL (F). å This end of the MODESTY Use two BLACK 1-7/8" FLAT HEAD SCREWS (X). PANEL (F) will hang past the end of the TOP (E2). BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) Page 16 109872 www.sauder.com/services...
  • Página 17 (2 used in this step) Do not overtighten the SCREWS (CC). S u r f a c i t h o I S T - L O F A S T E N ® E R S www.sauder.com/services 109872 Page 17...
  • Página 18 NOTE: Slide the END MOLDINGS (L) down until they celebrate! With a nap. å touch the MOLDINGS (I and J). * U.S. Pat. No. 5,499,886 å Slide the END MOLDING (L) onto the notched edges. Slide the END MOLDING (L) onto the notched edges. Page 18 109872 www.sauder.com/services...
  • Página 19 BLACK 1-7/8" FLAT HEAD SCREW (4 used for the BOTTOM) SUPPORT BRACKET (from the 109848 Return Kit) BLACK 9/16" LARGE HEAD SCREW (6 used from the 109848 Return Kit for the BRACKET from the Return Kit) www.sauder.com/services 109872 Page 19...

  • Página 20: Important

    BROWN 1-1/2" FLAT HEAD SCREWS (Y) with WASHERS (V) through the holes in the MODESTY PANEL and into the pre-drilled holes in the Inner End on the Desk. IMPORTANT: The 109872 U-Shape Connector Kit must be attached to the å 109843 Executive Desk as indicated in this step.
  • Página 21 Kit. Use three BROWN 1-1/2" FLAT HEAD SCREWS with WASHERS (from the 109848 Return Kit) through the holes in the modesty panel and into the pre-drilled holes in the INNER END on the Desk. IMPORTANT: The 109848 Return Kit must be attached to the 109872 U-Shape Connector Kit as å...
  • Página 22 NOTE: Notice the location of the two holes in the middle å of the INNER END (B). Push a SAUDER TWIST-LOCK® FASTENER (T) into the å indicated large holes shown in the INNER END (B). NOTE: Do not push TWIST-LOCK® FASTENERS into the å...
  • Página 23 Fasten the INNER END (B) to the MOLDINGS (I and J). å Tighten two TWIST-LOCK® FASTENERS. i t h ® f a c S u r - L O I S T E R S T E N F A S www.sauder.com/services 109872 Page 23...
  • Página 24 Fasten the INNER END (B) to the MODESTY PANEL (F). å Use two BLACK 1-7/8" FLAT HEAD SCREWS (X). This end of the MODESTY PANEL (F) will hang past the end of the TOP (E2). BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) Page 24 109872 www.sauder.com/services...
  • Página 25 (2 used in this step) Do not overtighten the SCREWS (CC). i t h o ® f a c S u r - L O I S T E R S T E N F A S www.sauder.com/services 109872 Page 25...
  • Página 26 NOTE: Slide the END MOLDINGS (L) down until they å leave without a bite. touch the MOLDINGS (I and J). * U.S. Pat. No. 5,499,886 å Slide the END MOLDING (L) onto the notched edges. Slide the END MOLDING (L) onto the notched edges. Page 26 109872 www.sauder.com/services...
  • Página 27 BLACK 1-7/8" FLAT HEAD SCREW (4 used for the BOTTOM) SUPPORT BRACKET (from the 109848 Return Kit) BLACK 9/16" LARGE HEAD SCREW (6 used from the 109848 Return Kit for the BRACKET from the Return Kit) www.sauder.com/services 109872 Page 27...
  • Página 28 BROWN 1-1/2" FLAT HEAD SCREWS (Y) with WASHERS (V) through the holes in the MODESTY PANEL and into the pre-drilled holes in the Inner End on the Desk. IMPORTANT: The 109872 U-Shape Connector Kit must be attached to the å 109843 Executive Desk as indicated in this step.
  • Página 29 Kit. Use three BROWN 1-1/2" FLAT HEAD SCREWS with WASHERS (from the 109848 Return Kit) through the holes in the modesty panel and into the pre-drilled holes in the INNER END on the Desk. IMPORTANT: The 109848 Return Kit must be attached to the 109872 U-Shape Connector Kit as å...
  • Página 30 å to step 21 of the 109843 instruction book. NOTE: You have the option of attaching the keyboard shelf from either the 109843 or 109848 to the 109872. å Insert the GROMMET (10P) into the large hole in the TOP (E2). Then, insert the GROMMET CAP (1P) into the GROMMET.

  • Página 31: Liste De Pièces

    élément et conserver le livret pour future référence. EXTRÉMITÉ EXTERNE ..........1 PLAQUE DE CONNECTEUR .......2 Pour contacter Sauder EXTRÉMITÉ INTERNE ..........1 COUVERCLE DE PASSE-CÂBLES ....1 en ce qui concerne cet MONTANT DROIT ............1 10P PASSE-CÂBLES ............1 élément, faire référence...
  • Página 32 Bureau ministre 109843, continuer avec l’étape 10. ÉTAPE 4 Pour fi xer le Kit de connecteurs en forme de U 109872 à la gauche du Bureau Ministre 109843, procéder à l’étape 18 maintenant. Fixer l’EXTRÉMITÉ EXTERNE (A) à la MOULURE COURTE (K).
  • Página 33 Avec l’ a ide d’une autre personne, positionner soigneusement le Kit trous indiqués dans l'EXTRÉMITÉ INTERNE (B). de connecteurs en forme de U 109872 à côté du Bureau ministre 109843 comme l'indique le schéma. REMARQUE : Ne pas enfoncer les FIXATIONS TWIST-LOCK® dans Fixer les deux PLAQUES DE CONNECTEURS (O) sur le bas des les deux autres grands trous dans l'EXTRÉMITÉ...
  • Página 34 Avec l’ a ide d’une autre personne, positionner soigneusement le Kit Fixer les MONTANTS (C et D) au VOILE DE FOND (F) et au de connecteurs en forme de U 109872 à côté du Bureau ministre DESSUS (E2). Serrer huit FIXATIONS TWIST-LOCK®.

  • Página 35: Lista De Partes

    EXTREMO EXTERNO ..........1 PLACA DE CONECTOR .........2 et conserver le livret pour future référence. EXTREMO INTERNO ..........1 CUBIERTA DE OJAL ...........1 Pour contacter Sauder PARAL DERECHO ............1 10P OJAL ..................1 en ce qui concerne cet PARAL IZQUIERDO .............1 PATA ..................2 élément, faire référence...

  • Página 36: Importante

    Se ofrecen dos opciones para el ensamblaje de esta unidad: Apriete dos SUJETADORES TWIST-LOCK®. Para fi jar el Kit conector en forma de U 109872 al lado derecho Cómo utilizar el SUJETADOR TWIST-LOCK® SAUDER del Escritorio Ejecutivo 109843 continúe con el paso 10.
  • Página 37 PASO 13 Con la ayuda de alguien, coloque con cuidado el Kit de Mesa Auxiliar 109848 al lado del Kit conector en forma de U 109872 tal Fije la MOLDURA CORTA (K) al PANEL SUPERIOR (E2). Utilice dos como se indica en el diagrama.
  • Página 38 TORNILLOS PLATEADOS DE CABEZA PERDIDA de 28 mm (CC). Con la ayuda de alguien, coloque con cuidado el Kit de Mesa Auxiliar 109848 al lado del Kit conector en forma de U 109872 tal NOTA: Alineé las esquinas de las MOLDURAS antes de apretar como se indica en el diagrama.

  • Página 39: Warranty

    à compter de la date d'achat la première fois et qui sont signalés à Sauder dans les limites de couverture de la contre tout défaut de matériaux ou de fabrication des composantes de mobilier Sauder.
  • Página 40 Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the Set a world record for speed? purchase and assembly process was a positive experience Feeling good about yourself? and you feel good about the furniture you just built. If you Nice.

Tabla de contenido