Installation Tips; Adjusting The Height Of The Shoulder Belts - Be Cool THUNDER iso-fi Instrucciones

THUNDER iso-fix
GB
1

INSTALLATION TIPS

1) The THUNDER ISO-FIX shall be used with
isofix anchors plus top tether for group I (9-
18kg child).
2) The THUNDER ISO-FIX must be used with
ISOFIX anchors (no top tether needed) at the
same time that with a 3-point seat belt for
group 2, 3 (15-36kg child).
3) The THUNDER ISO-FIX must be fitted as
a forward-facing position in the rear seats of
vehicle.
Four positions of the car seat
The THUNDER ISO-FIX can be used in four
different positions. (Fig. 1):
Pull the positioning handle under the front
of the seat forwards or backwards (feel the
spring underneath), then release the handle
on your required position while hearing a dis-
tinct click.
2 INSTALLATION
Installing method for Group I (9-18 kg)
a) Place the THUNDER ISO-FIX on the vehi-
cle's seat.
b) Rotate the adjuster button in anti-clock
wise direction (F2-A) and pull the isofix an-
chors out-wards as far as it goes, make sure it
can't be pushed back (F2-B)
c) Push the car seat towards the back of vehi-
cle's anchoring point (F3-A) and match the
isofix anchors to the vehicle's anchoring point
until hear a "click" (F3-B)
e) Rotate the adjuster button in anti-clock
wise direction (F4-A) and push the car seat to
the back of vehicle's seat as much as possible
(F4-B).
f) Hook the top tether up and pull as tight as
possible (F7).
3 Placing your child in the THUNDER ISO-
FIX car seat
Loosen the shoulder belts by pressing the
realease button and pull the shoulder belts
towards you.
Important: Do not pull on the belt pads when
doing so. (Fig. 8-9)
Press the red button to open the buckle.
(Fig. 10)
Part the belts over the sides of the shell.
(Fig. 11)
14
All manuals and user guides at all-guides.com
Place your child into the shell and make sure
that there are no toys or other hard objects in
the shell. (Fig. 12)
Match buckle tongue sections together and
insert them into the buckle. (Fig. 13)
f) Make sure the shoulder belts fit your child
snugly by pulling the adjuster belt. (Fig. 14)
Note! After you have done the installation,
check it by trying to move it, it shouldn't move
more than an inch side along the belt path,
if it does, tightens the straps or try installing
it again. The belts should never be twisted.
If you are unable to click the tongue sections
into the buckle, unlock the buckle by pressing
the red button and try again.
4
III (22-36 kg)
The installation method is for child within
Group II (15-25 kg) and Group III (22-36 kg).
a) Remove the harness system, including the
belt pads, central buckle and crotch strap.
b) Adjust the headrest by pulling the lifting
handle at your required position according to
your child's height.
c) Place your child into the car seat.
d) Thread the vehicle's shoulder belt from the
Group II belt guide slot (Fig. 14-a), or Group III
belt guide slot (Fig. 14-b), and thread the lap
belt into the belt guide hole (Fig. 14-c).
So the installation is completed (Fig. 14-d).
e) Joint the belts and buckle up.
5-6
belts
a) The correct height of the shoulder belts is
attained when the belt disappears into the
shell slightly above the shoulder of the child.
Ensure that the shoulder belts fit comfortably
over the child's shoulder. (Fig. 15)
b) Loosen the shoulder belts by pressing the
release button of the adjuster and pulling the
shoulder belts towards you as far as possible.
Important: Do not pull the belt pads when
doing so. (Fig. 9)
c) Place the shell of the seat in the sleeping
position.
d) Remove the shoulder belts from the yoke.
(Fig. 16-a)
e) Pull the shoulder belts through the belt
pads and belting slots in shell, ensuring that
Installing method for Group II (15-25 kg) /
Adjusting the height of the shoulder