Before Using The Equipment; Operation - EINHELL HEROCCO Manual De Instrucciones

tion is used.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
prolonged period or is not properly guided
and maintained.
Limit the operating time.
All stages of the operating cycle must be
considered (for example, times in which the
electric tools are switched off and times in which
the tool is switched on but operates without load).

5. Before using the equipment

Be sure to read the following information before
you put the cordless hammer drill into operation:
1. Charge the battery pack only with a charger
from the Power-X-Change series.
2. Only ever use sharp drill bits and screwdriver
bits which are suitable for the purpose and in
faultless condition.
3. Using a cable/pipe detector, check the area
you want to work on for concealed electric
cables and gas and water pipes.
5.1 Additional handle (Fig. 2/Item 10)
For safety reasons you must only use the
impact drill with the additional handle.
The additional handle (10) enables you to achieve
better stability whilst using the hammer drill. For
safety reasons the machine must not be used
without the additional handle (10).
The additional handle (10) is secured to the
hammer drill by a clamp. Turning the handle anti-
clockwise (viewed from the handle) will release
the clamp. Turning the handle clockwise tightens
the clamp.
Release the clamp of the additional handle fi rst.
Then you can swivel the additional handle (10)
into the most comfortable working position for
yourself. Now turn the additional handle (10) in
the opposite direction again until the additional
handle (10) is secure.
5.2 Fitting and adjusting the depth stop (Fig.
3/Item 11)
The depth stop (11) is held in position by a
number of locking points.
•
Press the button (a) and keep it pressed while
pushing the depth stop (11) into the guide.
•
Set the depth stop (11) to the same level as
the drill bit.
•
Pull the depth stop back by the desired
Anl_SA_Herocco_SPK8.indb 38 Anl_SA_Herocco_SPK8.indb 38
GB
drilling depth and then release the button (a).
•
The depth stop (11) will now have been
locked in position automatically.
•
Now drill the hole until the depth stop (11)
touches the workpiece.
5.3. Inserting a tool (Fig. 4)
Important! Set the changeover switch (3) to its
center position whenever you carry out any work
(for example changing the tool, maintenance
work, etc.) on the equipment.
•
Clean the tool before fitting it and apply a thin
coating of bit grease to the tool shaft.
•
Turn and push the dust-free tool into the tool
mounting (b) as far as it will go. The tool will
lock automatically.
•
Check that the bit is locked in placed by
pulling on it.
5.4. Removing a tool (Fig. 5)
Pull back and hold the locking sleeve (1) and
remove the tool.

6. Operation

6.1 Charging the LI battery pack (Fig. 6/7)
1. Remove the battery pack (5) from the handle,
pressing the pushlock button (6) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(8) into the socket outlet. The green LED will
then begin to fl ash.
3. Push the battery pack onto the battery
charger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
- 38 -
18.06.2018 13:02:20 18.06.2018 13:02:20