Technical Data; Before Starting The Equipment - EINHELL HEROCCO 18/20 Manual De Instrucciones

Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.

4. Technical data

Motor power supply: ............................18 V
No load speed: ..................... 0-1200 min
Clockwise/counter-clockwise: ........................Yes
Blow rate: ............................. 0-5500 min
Impact energy: .......................................1.6 ft./lbs
Drilling capacity
concrete/stone (max.): .....................
Weight: ......................................... 4.6 lbs (2.1 kg)
Wear ear-muff s.
The impact of noise can cause damage to
hearing.
Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect
condition.
•
Maintain and clean the equipment regularly.
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
CAUTION!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connection
with the equipment's con-struction and
layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is applied.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.
Anl_Herocco_18_20_SPK7_USA.indb 11 Anl_Herocco_18_20_SPK7_USA.indb 11
EN
Limit the operating time.
All stages of the operating cycle must be
considered (for example, times in which the
electric tools are switched off and times in which
the tool is switched on but operates without load).

5. Before starting the equipment

Be sure to read the following information before
you put the Cordless Rotary hammer into
(RPM)
-1
operation:
1. Charge the battery pack only with a charger
(RPM)
-1
from the Power X-Change series.
2. Only ever use sharp SDS-Plus drill bits which
are suitable for the purpose and in faultless
⁄ " (20 mm)
3
condition.
4
3. Using a cable/pipe detector, check the area
you want to work on for concealed electric
cables and gas and water pipes.
5.1 Additional handle (Fig. 2/Item 10)
For safety reasons you must only use the
Rotary hammer with the additional handle.
The additional handle (10) enables you to achieve
better stability whilst using the Rotary hammer.
For safety reasons the machine must not be used
without the additional handle (10).
The additional handle (10) is secured to the
impact drill by a clamp. Turning the handle anti-
clockwise (viewed from the handle) will release
the clamp. Turning the handle clockwise tightens
the clamp.
Release the clamp of the additional handle fi rst.
Then you can swivel the additional handle (10)
into the most comfortable working position for
yourself. Now turn the additional handle (10) in
the opposite direction again until the additional
handle (10) is secure.
5.2 Fitting and adjusting the depth stop (Fig.
3/Item 11)
The depth stop (11) is held in position by a
number of locking points.
•
Press the button (a) and keep it pressed while
pushing the depth stop (11) into the guide.
•
Set the depth stop (11) to the same level as
the drill bit.
•
Pull the depth stop back by the desired
drilling depth and then release the button (a).
•
The depth stop (11) will now have been
locked in position automatically.
•
Now drill the hole until the depth stop (11)
touches the workpiece.
- 11 -
06.04.2022 13:53:32 06.04.2022 13:53:32