Before Starting The Equipment; Operation - EINHELL TE-HD 18 Li-Solo Manual De Instrucciones Original

All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).

5. Before starting the equipment

Be sure to read the following information before
you use your cordless screwdriver for the fi rst
time:
1. Charge the battery pack with the charger
supplied. An empty battery pack requires a
charging period of approximately 0.5-1 hour.
2. Only ever use sharp drill bits and screwdriver
bits which are suitable for the purpose and in
faultless condition.
3. Always check for concealed electric cables
and gas and water pipes when drilling and
screwing in walls.

6. Operation

6.1 Charging the LI battery pack (Fig. 2-3)
1. Only Lithium –Ion Batteries from the Power-X-
Change series Einhell must be used. Please
choose at your convenience
Only the Lithium-Ion Battery Charger from the
Power-X-Change series Einhell can be used.
Please consult availability contacting Einhell
¡ATENTION! Product delivered WITHOUT
BATTERY and WITHOUT BATTERY
CHARGER
¡ATENTION! You must not use batteries and
battery charged which is not recommended
by the manufacturer
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(8) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 "Charger indicator" you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to become charged, ple-
ase check
•
whether there is voltage at the socket-outlet
•
whether there is proper contact at the char-
Anl_SA_TE_HD_18_Li_Solo_SPK8.indb 38 Anl_SA_TE_HD_18_Li_Solo_SPK8.indb 38
GB
ging contacts on the charger.
If the battery still fails to become charged, please
return
•
the charger
•
the battery pack
to our Customer Service Department.
To ensure that the LI battery pack provides
long service you should take care to recharge
it promptly. You must recharge the battery pack
when you notice that the power of the cordless
screwdriver drops.
6.2 Screw/Drill/Hammer drill selector switch
(Fig. 4/Item 2)
Caution! Change the switch position only
when the equipment is at a standstill!
Drilling/screwdriving:
For drilling/screwdriving, press the button (a) on
the selector switch (2) and simultaneously turn
the selector switch (2) to position A.
Hammer drilling:
For hammer drilling, press the button (a) on the
selector switch (2) and simultaneously turn the
selector switch (2) to position B.
Important.
You only require slight contact pressure for ham-
mer drilling. Excessive contact pressure will place
unnecessary strain on the motor. Check drill bits
at regular intervals. Sharpen or replace blunt drill
bits.
6.3 Changeover switch (Fig. 5/Item 3)
Using the slide switch above the On/Off switch
you can select the direction of rotation of the
equipment and lock the equipment so that it can-
not be switched on accidentally. You can select
between clockwise and counter-clockwise rotati-
on. To avoid causing damage to the gearing, the
direction of rotation must only be changed when
the equipment is at a standstill. When the slide
switch is in the middle position, the On/Off switch
is blocked.
Danger!
To avoid danger, the machine must only be
held using the two handles.
Otherwise you may suff er an electric shock if you
drill into electric cables!
- 38 -
06.11.2017 08:08:55 06.11.2017 08:08:55