Toshiba RAV-RM561FT-EN Instrucciones De Montaje página 69

[Procedure example]
Manual address setup procedure
While the operation stops, change the setup.
(Stop the operation of the unit.)
Field setting menu(2/2)
6. Setting timer operation mode
7. DN setting
8. Reset power consumption data
Return
Set
DN setting
1-1 2-2
1-2 3-1
2-1 3-3
Return
Unit Set
Address is displayed here.
3-3
DN setting
Code
(DN) Data
0012 0003
Return Fix
< >
3-3 DN setting
Code
(DN) Data
0012 0002
Return Fix
< >
135-EN
1
Push the [ MENU] button to display the
menu screen.
2
Push and hold the [ MENU] button and
∨
the [ ] button at the same time to
display the "Field setting menu".
Push and hold the buttons for more than 4
seconds.
3
∧ ∨
Push the [ button to select
] / [ ]
"7.DN setting" on the "Field setting menu"
screen, then push the " Set" [
Set
F2] button.
4
Push the " unit" [ F1] button to
Unit
select the indoor unit "3 - 3" to be changed
manually.
The selected unit changes as follows each time
the button is pushed:
1-1 1-2 3-3
5
Push the " Set" [ F2] button.
Set
The setting display for the selected unit
appears.
The fan and louver of the indoor unit operate.
When the group control is used, the fan and
louver of the selected indoor unit operate.
Line address change
Change "Code(DN)" from [0010] to [0012] with
∧ ∨
the [ ] / [ ] button.
Change "Data" from [0003] to [0002] with the
∧ ∨
[ ] / [ ] button.
Address is displayed here.
3-3 DN setting
Code
(DN) Data
0013 0003
Return Fix
< >
3-3 DN setting
Code
(DN) Data
0013 0002
Return Fix
< >
Address is displayed here.
3-3 DN setting
Code
(DN) Data
0014 0001
Return Fix
< >
3-3
DN setting
Code
(DN) Data
0014
0002
Return Fix
< >
– 68 –
6
Push the [ MENU] button to set the other
Code(DN) and Data. After "Continue?" is
displayed on the screen, push the
" Yes" [ F1] button.
Yes
Indoor address change
Change "Code(DN)" from [0010] to [0013] with
∧ ∨
the [ ] / [ ] button.
Change "Data" from [0003] to [0002] with the
∧ ∨
[ ] / [ ] button.
7
Push the [ MENU] button to set the other
Code(DN) and Data. After "Continue?" is
displayed on the screen, push the
" Yes" [ F1] button.
Yes
Group address change
Change "Code(DN)" from [0010] to [0014] with
∧ ∨
the [ ] / [ ] button.
Change "Data" from [0001] to [0002] with the
∧ ∨
[ ] / [ ] button.
8
Push the [ MENU] button to set the other
Code(DN) and Data. After "Continue?" is
displayed on the screen, push the
" No" [ F2] button to finish the
No
setting operation. " Setting" appears on
the screen for a while, then the screen
returns to the "Field setting menu" screen.
Pushing the " No" [ F2] button
No
displays the unit selection screen when the
group control is used. Push the [ CANCEL]
button on the unit selection screen to finish the
setting operation. " Setting" appears on the
screen for a while, then the screen returns to the
"Field setting menu" screen.
136-EN