ELICA IKONA LIGHT WH 60 Montaje Y Modo De Empleo página 26

Installation
Mounting
Before beginning installation:
• Check that the product purchased is of a suitable size for the
chosen installation area.
• Remove the charcoal (*) filter/s if supplied (see also relative
paragraph). This/these is/are to be mounted only if you want
lo use the hood in the filtering version.
• Check (for transport reasons) that there is no other supplied
material inside the hood (e.g. packets with screws (*),
guarantees (*), etc.), eventually removing them and keeping
them.
Expansion wall plugs are provided to secure the hood to most
types of walls/ceilings. However, a qualified technician must verify
suitability of the materials in accordance with the type of
wall/ceiling. The wall/ceiling must be strong enough to take the
weight of the hood.
Do not tile, grout or silicone this appliance to the wall. Surface
mounting only.
Mounting M1:
This type of cooker hood must be fixed to the ceiling.
Very heavy product; hood handling and installation must be
carried out by at least two persons.
Operation
To select the functions of the hood just touch the commands.
Light key ON/OFF
Intensive speed selection key (suction power) -
duration 5 minutes: the hood sets this power and
at the end of the 5 minutes returns to the previous
setting.
High-speed selection key (suction power).
Medium-speed selection key (suction power) -
when flashing it indicates the need to wash or
replace the carbon filter. This signal is normally
deactivated. To activate the alarm, disable the
electronic by pressing the 0 button for 3 seconds.
Next, simultaneously press buttons 1 and 2 for 3
seconds; at first, only button 1 will flash, then both
buttons 1 and 2 will flash to indicate activation.
Repeat the procedure to deactivate the alarm; at
first buttons 1 and 2 will flash and subsequently
only button 1 to indicate deactivation.
Low-speed selection key (suction power) – when
flashing it indicates the need to wash the fats filter.
Motor key OFF (stand by) – excludes the
electronics – reset wash/replace filters signals.
MOTOR OFF
Press briefly to switch the motor off.
RESET FILTERS SIGNALS
In functioning mode, after carrying out filter
maintenance, press the key until hearing the sound
signal. The flashing LED 1 (grease filter) or 2
(carbon filter) stops flashing.
EXCLUDING THE ELECTRONICS
Press the key for 3 seconds. The hood command
electronics will be excluded.
This function can be useful during the product
cleaning operations.
Just repeat the operation to reinsert the electronics.
If the hood fails to operate correctly, briefly disconnect it from the
mains power supply for almost 5 sec. by pulling out the plug. Then
plug it in again and try once more before contacting the Technical
Assistance Service.
Maintenance
Cleaning
Clean using ONLY a cloth dampened with neutral liquid detergent.
DO NOT CLEAN WITH TOOLS OR INSTRUMENTS. Do not use
abrasive products. DO NOT USE ALCOHOL!
Grease filter
Fig. 11-25
The grease filter must be cleaned once a month using non
aggressive detergents, either by hand or in the dishwasher, which
must be set to a low temperature and a short cycle. When washed
in a dishwasher, the grease filter may discolor slightly, but this
does not affect its filtering capacity.
Charcoal filter (filter version only)
Fig. 24
Circular charcoal filter
Apply one on each side as cover to both the shield grids of the
motor impeller, then turn clockwise.
For the disassembly, turn counter-clockwise.
The saturation of the charcoal filter occurs after more or less
prolonged use, depending on the type of cooking and the regularity
of cleaning of the grease filter.
In any case it is necessary to replace the cartridge at least every
four months.
The charcoal filter may NOT be washed or regenerated.
Replacing lamps
The hood is equipped with a lighting system based on LED
technology.
The LEDs guarantee an optimum lighting, a duration up to 10
times longer than the traditional lamps and allow to save 90%
electrical energy.
To replace lights, contact authorised spare part center.
23