Toto CST412MF Instrucciones Para La Instalación página 2

1
Piping and Rough-In Check
In order for your new TOTO toilet to fit correctly, please check the following
dimensions.
1. Distance between finished
wall and teh center of the
floor drain, "RI", must be 12"
(305mm) or 10" (254mm) for
CST412MF.10
2. Water supply should be ap-
proximately 8" to 10" to the
left (facing the bowl) from the
center line of closet flange, and
approximately 6" above the
finished floor.
3. Using the provided template,
confirm the installation dimen-
sions of the PVC trap and the
mounting blocks.
Represents dimension for
CST414M.
7-½" (190mm) - CST414M
A
7- ⁄ " (200mm) - CST412MF,
7
8
CST412MF.10 & CST416M.
8-½" (215mm) - CST464MF.
1-¾" (45mm) - CST412MF.10
B
2-½" (63mm) - CST414M
3- ⁄ " (85mm) - CST412MF & CST416M.
3
8
3-½" (88mm) - CST464MF
2
PVC Trap and Mounting Block Installation
Removing Existing Toilet (If Necessary)
a) Turn-off water supply and flush the toilet.
b) Remove remaining water from bowl and tank.
c) Disconnect water supply and remove tank and bowl.
d) Remove old wax seal and mounting bolts.
■ Place the installation template so that the baseline of the template and the
center line of the closet flange line up.
Mark the screw locations for the PVC trap and mounting blocks.
■ Drill 11/64" screw holes at the marked locations unless toilet is being installed
on a tile or concrete floor. In the case of tile or concrete floor installation, drill
5/16" inch holes and use provided plastic anchors.
Installing Mounting Bolts
a) Clean debris from closet flange
b) Install the mounting bolts into the slot of the
flange head down with the threaded shank of the
bolt pointed upward as shown.
Installing PVC Trap & Mounting blocks
a) Turn the PVC outlet connection upside down.
b) Firmly press a new wax seal onto the circular recess around the outlet opening.
c) Turn the outlet connection upright and lower it onto the position over the closet
flange.
d) With the unit properly aligned, press down firmly to set the wax seal.
DO NOT REMOVE THE OUTLET CONNECTION
AFTER THE WAX SEAL IS SET.
CAUTION
■ Install washer and nut on the T-bolt to secure PVC trap to flange. Nut should
be tightened 1/2 turn after hand-tight
Secure the back side of the PVC trap to the floor using the provided screws.
■
Level the PVC outlet. DO NOT USE EXCESSIVE FORCE.
■ Install the mounting blocks using the provided screws, washers, and anchors.
Ensure that blocks are firmly connected to the floor. If necessary, use the
provided template for the proper alignment.
2
Supply Valve
Closet Flange
6-⅝" (160mm)
A
6" (152mm)
■ With holes location properly marked, drill holes
On wood floor installation;
³⁄ "
for Modular Rough-In
³²
"
⁄
11
for Mounting Blocks
64
On concrete/tile installation;
"
⁄
9
for Modular Rough In using green anchors
32
"
⁄
C/L 11 for Mounting Block using white anchors
32
TO PREVENT WATER AND ODOR LEAKAGE
PLEASE ENSURE THAT WAX SEAL IS FITTED
PROPERLY BETWEEN THE SOCKET AND
FLANGE. DO NOT OVER TIGHTEN THE NUTS,
CAUTION
DAMAGE TO PLASTIC PARTS MAY RESULT.
3
*CST414
Rough in
4
Installation of Mounting Hardware to Bowl
Tank Mounting hardware is included in the tank.
Install mounting hardware to bowl as shown.
Mounting hardware is include in the TS810DV2 bag.
5
Installation of Bowl to PVC Outlet
Put the outlet of the toilet bowl to the mouth of the PVC
outlet, then slide the water closet into socket until it
reaches the wall.
*CST414
In order to prevent leakage, be sure to
insert toilet all the way into the socket.
CAUTION
Wax Seal
(not included)
*CST412
CST416
CST464
Rough in
*CST412
CST416
CST464
12" (305mm) or
10" (254mm) for
CST412MF.10