Frico AD 300A/E Manual Del Usuario página 28

Thermozone AD300A/E, AD400A/E
the pressure. An angle up to 15° Тs reМommenНeН. THe
more loaН МauseН bв negatТve pressure, temperature
НТfferenМes anН аТnН, the more shoulН the aТr beam be
НТreМteН outаarНs.
Basic air low settinРs
The aТr loа Тs set аТth the aТr loа seleМtor so that the
speeН of the aТr Тs 3-4 m/s 1m above the loor. The
НТreМtТon of the aТr beam anН the aТr speeН maв neeН
to be aНУusteН more eбaМtlв НepenНТng on the loaН on
the Нoor.
AdjustinР the air curtain and air stream
The НТreМtТon anН the veloМТtв of the aТr stream shoulН
be aНУusteН Тn regarН to the loaН on the Нoorаaв. Pres-
sure forМes the aТr stream to benН toаarНs the ТnterТor
of the room (аhen the room Тs heateН anН the eбterТor
Тs МolН).
The aТr stream shoulН be НТreМteН outаarНs to resТst
the pressure. An angle up to 15° Тs reМommenНeН. The
more loaН МauseН bв negatТve pressure, temperature
НТfferenМes anН аТnН, the more shoulН the aТr beam be
НТreМteН outаarНs.
Basic air low settinРs
The aТr loа Тs set аТth the aТr loа seleМtor so that the
speeН of the aТr Тs 3-4 m/s 1m above the loor. The
НТreМtТon of the aТr beam anН the aТr speeН maв neeН
to be aНУusteН more eбaМtlв НepenНТng on the loaН on
the Нoor.
Trouble shootinР
If the fans stanН stТll, МheМk the folloаТng:
a) Poаer supplв; МheМk fuses, МТrМuТt-breaker,
tТme sаТtМh (Тf anв) that starts anН stops
the unТt.
b) That the aТr loа seleМtor Тs МorreМtlв set.
М) That the posТtТon lТmТt sаТtМh Тs аorkТng
(Тf anв).
If the error Мannot be iбeН, please МontaМt qualТieН
servТМe teМhnТМТan.
If there Тs no heat, МheМk the folloаТng:
a) Poаer supplв to eleМtrТМ heater; МheМk fuses anН
МТrМuТt-breaker (Тf anв).
b) Thermostat settТngs anН aМtual temperature.
М) That the output seleМtor (Тf anв) Тs set
МorreМtlв.
Н) That the overheat proteМtТon has not been
releaseН.
OverheatinР (applies to units with electric heat)
The Thermoгone Тs equТppeН аТth an overheat proteМtor.
If Тt Тs releaseН Нue to overheatТng, reset as folloаs:
1) DТsМonneМt the eleМtrТМТtв аТth the fullв ТsolateН
sаТtМh.
2) InvestТgate the matter anН repaТr the fault.
3) Reset Тs performeН as folloаs:
• LoМate the reН button аhТМh Тs loМateН ТnsТНe
the unТt at the Тnner gable to аhТМh the fan anН
the motor are attaМheН. Вou Мan see Тt Тf вou
remove the front plate, see page 2.
• Press the button untТl a МlТМk Тs hearН
4) ConneМt the Thermoгone agaТn.
If the error Мannot be iбeН, please МontaМt qualТieН
servТМe teМhnТМТan.
Maintenance
Note! DТsМonneМt eleМtrТМТtв prТor to МleanТng or ТnspeМ-
tТon (unТts аТth eleМtrТМ heat Мan be supplТeН from more
than one МonneМtТon).
The fan motors anН the other Мomponents requТre
no maТntenanМe other than МleanТng аhen neМessarв,
hoаever at least onМe вear. GrТlle, Тmpeller anН ele-
ments are vaМuum МleaneН or НrТeН Мlean аТth a Нamp
Мloth. Open the ТnspeМtТon hatМh to reaМh elements anН
Тmpellers.
SaПety cut-out
(applies to units with electric heat)
If the ТnstallatТon Тs proteМteН bв means of a safetв Мut-
out, аhТМh trТps аhen the applТanМe Тs МonneМteН, thТs
maв be Нue to moТsture Тn the heatТng element. Аhen
an applТanМe МontaТnТng a heater element, has not been
useН for a long perТoН anН Тs storeН Тn a Нamp envТron-
ment, moТsture Мan enter the element. ThТs shoulН not
be seen as a fault, but Тs sТmplв reМtТieН bв МonneМtТng
the applТanМe to the maТns supplв vТa a soМket аТthout a
safetв Мut-out, so that the moТsture Мan be НrТven out of
the element.
The НrвТng tТme Мan varв from a feа hours to a feа
Нaвs. As a preventТve measure the Thermoгone shoulН
oММasТonallв be run for a short tТme аhen Тt Тs not beТng
useН for an eбtenНeН perТoН of tТme.
The Рarantee is only valid iП the Thermozone
units are used in the manner intended by the
manuПacturer and in accordance with the installation
and maintenance instructions.
GB
'
27