ELICA IKONA MAXXI PURE Serie Montaje Y Modo De Empleo página 69

T3:
FUMES EXTRACTOR (A) - speed 3 and "BOOST"
selection key
Press once to activate the high speed (extraction power);
Press again to switch to "BOOST" speed. The LED T3 will
start flashing.
When the booster is on, it is possible to switch to the first or
second speed by pressing the desired speed button T1 or T2.
When the booster is on, press T3 again to turn the hood off.
After 5' the booster automatically turns off and the third speed
is automatically activated.
T4:
Light ON/OFF key
Press to activate / deactivate lighting on the TOP.
T6 PURIFIER (B) low speed selection key
A short press activates the Air Purifier at low speed,
A long second press (2 sec.) activates the motor in timed
mode. The LED T6 will start flashing, the motor will
automatically turn off after 6 hours. To stop the timed mode at
any time, press T6 again
If T6 is pressed a second time with the timer deactivated, the
Purifier motor will turn off.
T5 PURIFIER (B) intensive speed selection key
Press to activate the Air Purifier at intensive speed.
Press T5 again to turn the Purifier motor off.
Note: this speed is always timed at the end of the 40 min,
after which the speed switches to the first purifier speed (the
one normally activated with key T6), and 6h timing will start
automatically.
Motor "DELAY OFF" Mode:
A long press of key T1 / T2 / T3 activates automatic motor
power-off.
The motor will turn off after the following time period:
T1 = after 20 minutes;
T2 = after 15 minutes;
T3 = after 10 minutes.
Notes: This function cannot be programmed for the "BOOST"
speed. When Delay OFF is active, pushing the key of any
speed will disable the function.
Fumes Extractor motor (A) and Purifier motor (B) Priority
Management:
The Fumes Extractor motor (A) has priority over the Air
Purifier with HEPA filters motor (B).
With motor (A) and (B) in OFF: either of the two motors can be
activated at any time.
With Fumes Extractor (A) active:
- If the Fumes Extractor (A) is running, pressing keys T6-T5
will activate the "DELAY OFF" mode of the Fumes Extractor
motor (A), and the Purifier will automatically turn on following
the operation of the "DELAY OFF" mode. In this case, the
LED of the active speed T1 / T2 / T3 will start flashing and the
LED of the selected T5 or T6 key will light up steady
If the Fumes Extractor (A) is running and activation of the
purifier has already been programmed, a second long press of
key T6 in low speed will cause the Purifier to automatically
turn on in timed mode, following the operation of the Delay
OFF mode. In this case the LED of the active speed T1 / T2 /
T3 will start flashing together with the LED of key T6.
Purifier (B) active:
- If the Purifier (B) is running, pressing keys T1-T2-T3 will
cause the Purifier (B) to immediately turn off, and the Fumes
Extractor motor (A) will be activated
Filters saturation INDICATOR:
The hood warns the user at regular intervals that the filters
have to be cleaned/replaced.
With the T1 key lit and the +T2 key flashing, it is necessary to
replace the Grease Filter
With the T1 key lit and the +T3 key flashing, it is necessary to
replace the Carbon Filter
With the T5 and +T6 keys flashing, it is necessary to replace
the HEPA Filter
Note: the indication of filters saturation is visible only within
the first 10 seconds of turning on the hood.
RESET Filters saturation Alarm:
Only if the Filters saturation alarm is displayed:
pressing keys T1+T2 simultaneously for about 3 seconds will
reset the Grease Filter saturation alarm.
pressing keys T1+T3 simultaneously for about 3 seconds will
reset the Carbon Filter saturation alarm.
At any time, even if the filters saturation alarm is not
displayed, pressing keys T5+T6 simultaneously for about 3
seconds will reset the HEPA Filter saturation alarm.
ACTIVATE / DISABLE the Filters counter.
With motor (A) and (B) in OFF, pressing keys T2+T3
simultaneously will open the Filters saturation indicator
management menu.
From this menu:
 Pressing the T2 key activates / disables the Grease Filter
indicator.
Note: The Grease Filter is ACTIVATED as the default setting.
 Pressing the T3 key activates / disables the Carbon Filter
indicator.
Note: The Carbon Filter is DISABLED as the default setting.
Pressing keys T2+T3 again will close the menu and save the
changes made.
68