Restart Protection; Cutting Depth; Changing Tools; Setting The Riving Knife - Festool PRECISIO CS 50 EB Instrucciones De Servicio/Lista De Piezas De Repuesto

5.6

Restart protection

The built-in undervoltage release prevents
that the machine restarts on its own in the
continu-ous operation mode following a
power cut. In this case, the machine must
fi rst be switched off and then on again.
6 Machine settings
Prior to any setting, maintenance or
repair, pull the mains plug!
To make setting easier, the saw unit can
be locked in the front position (Fig. 5):
pull the saw unit forwards as far as it will
go and place the switch (5.1) in the lower
position.
The machine must not be used in
the front position!
6.1

Cutting depth

The cutting depth can be set steplessly (0
- 50 mm with 90° position of the saw blade)
by turning the crank handle (5.4).
6.2 Mitre
The saw blade can be pivoted between 0°
and 45°:
- Open the rotary knob (5.3).
- Set the mitre using the scale (5.6) by
turning the handle (5.2).
- Close the rotary knob (5.3).
For exact fi tting work (relief cutting on the
bordering), the saw blade can be pivoted
2° beyond the two end positions. To do so,
the button (5.5) is pressed in the end posi-
tion; the saw blade can then be pivoted up
to -2° or 47°. On pivoting back, both end
positions are active once again.
6.3

Changing tools

Safety Instructions Fast-Fix Ten-
sion Nut (see Fig. 7 A).
After tensioning, close the handle
bow.
Only tighten or loosen the Fast-Fix
Tension Nut by hand. Under no cir-
cumstances use the handle bow with
aid of screwdrivers, pliers, or other
tools for tightening or loosening.
If the nut cannot be loosened by
hand, only use a pin-type face span-
ner for support.
All manuals and user guides at all-guides.com
- Open the locking mechanism (1.3) and
- Open the locking mechanism (6.1) and
- Shift the lever (7.5) and turn clockwise
- Change the tool. In doing so, bear in
- Firmly tighten the Fast-Fix clamp (7.4)
- Swing the saw blade cover (6.2) upwards
- Insert the bench insert with the rear edge
6.4
The spacer wedge (7.1) is to be set in such
a way that the gap to the chuck of the saw
blade is 3 to 5 mm.
- Use the Allen key (6.3) to remove the
- After both of the screws (8.3) have been
- After completion of the setting, fi t the
6.5
As shown in Fig. 3, the supplied guide can
be secured to all four sides of the machi-
ne.
The guide offers the following adjustment
options:
17
Never continue to use the Fast-Fix
nut, in case the handle bow is loose
or damaged.
Due to the special shank, only the
saw blades offered by Festool for
this machine may be used.
remove the bench insert (1.2) upwards
swing the saw blade cover (6.2) down.
This automatically locks the tool spindle
(left-hand thread) to open the Fast-Fix
clamp (7.4)
mind:
• The Fast-Fix clamp (7.4), fl ange (8.1)
and saw blade must be clean
• The direction of rotation on the saw
blade (7.6) must match the direction of
rotation of the machine (7.7)
• Place the saw blade on the centre of the
fl ange (8.1) and turn until the contour of
the fl ange and the saw blade hole lock.
anticlockwise; shift the lever (7.5)
and close the locking mechanism (6.1)
fi rst (see Fig. 9) and close the locking
mechanism (1.3).

Setting the riving knife

screw (7.3) and take it out together with
the clamping element (7.2),
opened, the guide element (8.2) can be
shifted vertically to set the gap between
the spacer wedge and saw blade.
spacer wedge and clamping element again
and tighten all screws.
Guide