Protecting The Environment - DeWalt DWE4212 Manual De Instrucciones

ENglIsh
Cutting Stone
The machine shall be used only for dry cutting.
For cutting stone, it is best to use a diamond cutting
disc. Operate the machine only with additional dust
protection mask.
Working Advice
Exercise caution when cutting slots in structural walls.
Slots in structural walls are subject to the country-
specific regulations. These regulations are to be observed
under all circumstances.Before beginning work, consult
the responsible structural engineer, architect or the
construction supervisor.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the
risk of eye injury, always wear approved eye protection
when performing this.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories

WARNING: Since accessories, other than those
offered by D WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center.
Repairs
The charger and battery pack are not serviceable.

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should
be performed by a D WALT factory service center
e
42
or a D WALT authorized service center. Always use
e
identical replacement parts.

Protecting the Environment

Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions.
DWE4212-B3 DWE4212-B2 DWE4212-BR DWE4212-AR
DWE4214-B3 DWE4214-B2 DWE4214-BR DWE4214-AR
DWE4227-B3 DWE4227-B2 DWE4227-BR DWE4227-AR
Power 1 200 W
Voltage 120 V~
50–60 Hz
Frequency
Speed (RPM): 11 000/min 11 000/min 11 500/min 11 000/min
DWE4314-B3 DWE4314-B2 DWE4314-BR DWE4314-AR
DWE4315-B3 DWE4315-B2 DWE4315-BR DWE4315-AR
Power
Voltage
Frequency
Speed (RPM): 11000/min
DWE4336-B3 DWE4336-B2 DWE4336-BR DWE4336-AR
Power
Voltage
Frequency
Speed (RPM): 2800-10000/
WALT
e
specifications
1 200W 1 200W
220V~ 127V~
50–60 Hz 60 Hz
1500W 1500W 1500W
120V~ 220V~ 127V~
50-60Hz 50-60Hz 60Hz
11000/min 11000/min
1500W 1500W 1500W
120V~ 220V~ 127V~
50-60Hz 50-60Hz 60Hz
2800-10000/ 2800-10000/
min min min
1 200W
220V~
50 Hz
1500W
220V~
50Hz
11000/min
1500W
220V~
50Hz
2800-10000/
min