Stryker IsoTour Manual De Operación página 26

R R e e c c o o m m m m e e n n d d e e d d s s e e p p a a r r a a t t i i o o n n s s d d i i s s t t a a n n c c e e s s b b e e t t w w e e e e n n p p o o r r t t a a b b l l e e a a n n d d m m o o b b i i l l e e R R F F c c o o m m m m u u n n i i c c a a t t i i o o n n e e q q u u i i p p m m e e n n t t a a n n d d t t h h e e 2 2 8 8 7 7 4 4
380-390
430-470
704-787
800-960
1,700-1,990
2,400-2,570
5,100-5,800
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters
(m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output
power rating of the transmitter in watts (W) according to the transmitter manufacturer.
N N o o t t e e - - These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
The 2874 I I s s o o T T o o u u r r pump is suitable for use in the electromagnetic environment specified below. The customer or the
user of the 2874 I I s s o o T T o o u u r r pump should assure that it is used in such an environment.
I I m m m m u u n n i i t t y y t t e e s s t t
Electrostatic Discharge
(ESD)
IEC 61000-4-2
Electrostatic fast transient/
burst
IEC 61000-4-4
Surge
IEC 61000-4-5
EN 22
TETRA 400
GMRS 460;
FRS 460
LTE Band 13, 17
GSM 800/900;
TETRA 800;
iDEN 820;
CDMA 850;
LTE Band 5
GSM 1800;
CDMA 1900;
GSM 1900;
DECT;
LTE Band 1, 3, 4, 25;
UMTS
Bluetooth;
WLAN;
802.11 b/g/n;
RFID 2450;
LTE Band 7
WLAN 802.11 a/n
G G u u i i d d a a n n c c e e a a n n d d m m a a n n u u f f a a c c t t u u r r e e r r ' ' s s d d e e c c l l a a r r a a t t i i o o n n - - e e l l e e c c t t r r o o m m a a g g n n e e t t i i c c i i m m m m u u n n i i t t y y
I I E E C C 6 6 0 0 6 6 0 0 1 1 t t e e s s t t l l e e v v e e l l
+8 kV contact
+15 kV air
+2 kV for power supply lines
+1 kV for input/ output lines
±1 kV for input/output lines
I I s s o o T T o o u u r r p p u u m m p p
1.8
2.0
0.2
2.0
2.0
2.0
0.2
C C o o m m p p l l i i a a n n c c e e l l e e v v e e l l
+8 kV contact
+15 kV air
+2 kV for power supply lines
+1 kV for input/ output lines
±1 kV for input/output lines
0.3
0.3
0.3
0.3
0.3
0.3
0.3
E E l l e e c c t t r r o o m m a a g g n n e e t t i i c c
e e n n v v i i r r o o n n m m e e n n t t - - g g u u i i d d a a n n c c e e
Floors should be wood,
concrete, or ceramic tile. If
floors are covered with
synthetic material, the
relative humidity should be
at least 30%.
Main power quality should
be that of a typical
commercial or hospital
environment.
Main power quality should
be that of a typical
commercial or hospital
environment.
2874-009-005 Rev A.0