Cleaning, Maintenance And Ordering Spare Parts; Replacing The Cutting Line - EINHELL AGILLO Manual De Instrucciones

7. Cleaning, maintenance and
ordering spare parts
HAZARD!
Before putting away or cleaning the grass
trimmer, switch off and remove the battery pack.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
We recommend cleaning the equipment
immediately each time after use.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may
be aggressive to the plastic parts in the
equipment. Ensure that no water can get into
the interior of the equipment. The ingress of
water into an electric power tool increases the
risk of an electric shock.
•
Use a brush to remove deposits from the
safety guard.
7.2 Replacing the line spool
Danger! Remove the battery packs!
1. Fig. 21 Press the line spool housing together
at the marked points and remove the spool
cover.
2. Take out the empty line spool and the
pressure spring.
3. Fig. 22 Thread the end of the line on the new
line spool through the eyelet in the spool
cover and allow approx. 5.1 in. (13 cm) of line
to project. Insert the pressure spring (34) in
the line spool.
4. Press the spool cover back into the line spool
housing.

7.3 Replacing the cutting line

Danger! Remove the battery packs!
1. Fig. 21 Press the line spool housing together
at the marked points and remove the spool
cover.
2. Take out the empty line spool and the
pressure spring.
3. Remove any remaining cutting line if there is
any.
4. Fig. 23 Insert the new cutting line through the
line mount inside the spool.
5. Wind the line with tension in a counter-
clockwise direction.
Anl_Agillo_SPK7_USA.indb 20 Anl_Agillo_SPK7_USA.indb 20
EN
6. Fig. 24 Hook the line, approx. 5.9 in. (15 cm)
before the end of the line, into one of the line
holders on the edge of the spool.
7. Fig. 22 Thread the end of the line on the new
line spool through the eyelet in the spool
cover. Insert the pressure spring (34) in the
line spool.
8. Pull the line sharply to release it from the line
holder.
9. Press the spool cover back into the line spool
housing.
When you start the equipment again the line will
be cut to the perfect length automatically.
Caution! Bits of the nylon line could cause
injury when fl ung out.
7.4 Sharpening the guard hood blade
The guard hood blade (Fig. 2/Item 14) can
become blunt over time. When you notice this,
undo the screw holding the guard hood blade
on the guard hood. Clamp the blade in a vise.
Sharpen the blade with a fl at fi le and make sure
that the angle of the cutting edge is not altered in
the process. File in one direction only.
7.5 Maintenance
There are no other parts inside the equipment
which require maintenance.
7.6 Ordering replacement parts:
Service
1. If your power tool requires service,
contact an authorized Einhell USA dealer
or call the Einhell USA customer service
center at 1-866-EINHELL
(1-866-346-4355). Only identical
replacement parts should be utilized for
repairs. This will ensure that the safety of the
power tool is maintained.
2. If the battery charger cable is damaged, it
must be immediately replaced to avoid a
hazard. Contact the Einhell USA
service center at 1-866-EINHELL
(1-866-346-4355) for assistance.
- 20 -
customer
®
05.08.2019 10:37:31 05.08.2019 10:37:31