Preventative Maintenance - Vollrath InstaCut 3.5 Manual Del Operador

CLEANING
WARNING
Sharp Blade Hazard
Blades are sharp and can cause cuts. To avoid injury from
sharp blades, handle with caution.
NOTICE: Food acids will dull the blades and corrode the metal.
Always clean this food preparation equipment immediately
after every use.
NOTICE: Do not put this equipment in a dishwasher or dish machine
with soaps, detergents, or other alkaline chemicals that
can harm the equipment.Handwash only.
NOTICE: Do not use abrasive materials, scratching cleansers or
scouring pads to clean this equipment. These can damage
the finish.
Disassemble
1. Remove the pusher head assembly:
Table top models. Slide the pusher head off the guide rods.
Wall mount models. Remove the locking pin. Lift the handle and
slide the pusher head off the guide rods. Place the locking pin back
into the hole on the handle assembly to prevent it from being lost.
2. Remove the two thumbscrews and
separate the pusher block from the
pusher head.
3. Raise the bumpers approximately 2"
(5.0 cm).
4. Loosen the thumbscrew and carefully
remove the blade assembly.
Wash
1. Wipe, rinse or spray off equipment, pusher head and blade assembly
thoroughly with HOT water.
2. Do not wipe across the blades.
NOTICE: Wiping across the sharp edge of the blade can cause
injury and will dull the blades.
3. Clean the blade assembly by forcing water, under pressure, through
the blades from the unsharpened side. If necessary, use a nylon
bristle cleaning brush to push food particles out from the
unsharpened side of the blade assembly.
4. Let the equipment air dry.
™
InstaCut 3.5 Slicer, Dicer, Wedger and Corer Operator's Manual
Reassemble
1. Install the cutting blade assembly into the base. Tighten the
thumbscrew to push blade assembly securely against the other side.
2. Lubricate the guide bar with mineral oil or Petrol-Gel.
NOTICE: Do not use cooking oil as it will become sticky and may
permanently damage the equipment.
3. Slide the bumpers into place.
4. Reassemble the pusher head and pusher block together.
5. Install the pusher head assembly:
Table top models. Reassemble the pusher head assembly.
Wall mount models. Remove the locking pin from its storage
location on the handle assembly. Lift handle and slide the pusher
head on the guide rods. Place locking pin back into the hole through
the handle assembly and the pusher head.

PREVENTATIVE MAINTENANCE

1. Clean the equipment after every use.
2. Use for intended purposes only.
3. Change the blades regularly – based on usage.
REPLACE THE BLADE ASSEMBLY
WARNING
Sharp Blade Hazard
Blades are sharp and can cause cuts. To avoid injury from
sharp blades, handle with caution.
Wash new blades with warm, soapy water and rinse thoroughly to
remove the thin protective oil film. Keep the sharp edge away from you
when handling blades.
1. Familiarize yourself with the parts diagram for your equipment.
2. Remove the pusher head assembly:
Table top models. Slide the pusher head off the guide rods.
Wall mount models. Remove the locking pin. Lift handle and slide
the pusher head off the guide rods. Place pin back into the hole on
the handle assembly to prevent loss.
3. Raise the bumpers approximately 2" (5.0 cm).
4. Loosen thumbscrew and carefully remove the blade assembly.
Remove the cutting blade assembly by pressing upwards on the
bottom of the side of the blade holder, where the thumbscrew is
located. Discard the old blade assembly.
5. Install the new cutting blade assembly by inserting the tab on the
blade holder into the groove in the base, then lowering the blade
holder into the seated and flush position in the base. Tighten the
thumbscrew
6. Slide bumpers down guide rods to contact base assembly. Position
pusher head assembly onto the guide rods, slowly lower pusher
head assembly, and check pusher head block to blade alignment.
7. Lubricate the guide rods with mineral oil or Petrol-Gel after each
use. Do not use cooking oil as it will become sticky and may
permanently damage the equipment.
3