stayer SC250W Manual De Instrucciones página 51

Adjusting the horizontal mitre angle to +- 45º
IMAGES A B R I
Checking
1.Raise locking bolt 14 (SC2500W, Turn the locking knob
14 toward the left and press the button 53 to move the
head).
2.Move the head horizontally until it locks at +45º
(SC2500W/SC2600W Rotate the knob 14 to adjust the
head in the desired position).
3.Check that the indicator for horizontal angles marks
exactly 45º. If not, proceed to adjusting.
4.Repeat the same sequence for the horizontal angle at
-45º.
Adjusting
1.Keep locking bolt 14 raised .
2.Loosen fastening screw of cam 33.
3.Move the whole of head and cutting table horizontally
until it locks at 45º.
4.Turn cam 33 against guide 13 until indicator 9 coincides
with the 45º marking of indicator 7.
5.Tighten the fastening screw of cam 33.
6.Release locking bolt 14.
7.Repeat the same sequence for the horizontal angle at
45º.
Adjustment for SC2500W / SC2600W
1.Turn the locking knob 14 to the left, and click the button
53 to move the head.
2.Horizontally move the head assembly and cutting table
up to 45 degrees.
3.Release the button 53 of the locking knob 14 and turn
right to secure.
4.Repeat the same sequence for the horizontal angle of
-45 degrees.
Adjusting the vertical mitre angle to 90º
IMAGES A B G
Checking
1.Release vertical adjustment of the head by loosening
control element or nut 15 (with Allen key).
2.Move head to the right stopper (90º).
3.Lock the vertical adjustment of the head by tightening
control element or nut 15 (with Allen key).
4.Check the angle by means of a duly calibrated angle
chart or a goniometer (minimum precision +- 5º)
applying one of the surfaces thereof on cutting table 6
and the other on cutting disk 21.
5.Should the side of the angle chart not adjust exactly to
the disk or if the direct measurement of the goniometer
reached a deviation of more than +- 20º, proceed to
adjusting.
Adjusting
1.Release the vertical adjustment of the head by loosening
control element or nut 15 (with Allen key).
2.Move the head to the right stop (90º).
3.Remove retainer nut 18.
ENGLISH
51
4.Place a goniometer (minimum precision +- 5º) applying
one of its sides on cutting table 6 and the other on
cutting disk 21.
5.Act on adjusting screw 19 until obtaining a measurement
of 90º.
6.Fasten the adjustment by tightening retainer nut 18
whilst retaining screw 19 with a screwdriver so as to
prevent it from moving.
7.Block the vertical adjustment of the head by tightening
control element or nut 15 (with Allen key).
Adjusting the vertical mitre angle to 45º
IMAGES A E
Checking
1.Release the vertical adjustment of the head by loosening
control element or nut 15 (with Allen key)
2.Move head to the left stop (45º).
3.Block the vertical adjustment of the head by tightening
the control element or nut 15 (with Allen key).
4.Check the vertical adjustment by means of a duly
calibrated angle chart or a goniometer (minimum
precision +- 5º) applying one of its sides on cutting
table 6 and the other on cutting disk 21.
5.Should the side of the angle chart not adjust exactly to
the disk or if the direct measurement of the goniometer
reached a deviation of more than +- 20º, proceed to
adjusting.
Adjusting
1.Release the vertical adjustment of the head by loosening
control element or nut 15 (with Allen key).
2.Move head to the left stopper (45º).
3.Remove retainer screw 17.
4.Check the vertical adjustment by means of a duly
calibrated angle chart or a goniometer (minimum
precision +- 5º) applying one of its sides on cutting
table 6 and the other on cutting disk 21.
5. Act on adjusting screw 16 until obtaining a measurement
of 45º on the goniometer or until the surface of the
angle chart that contacts the disk has full (it does not
allow any light to pass through) contact.
6.Fasten the adjustment by tightening retainer screw 17
whilst retaining screw 16 with a screwdriver so as to
prevent it from moving.
7.Block the vertical adjustment of the head by tightening
control element or nut 15 (with Allen key).
Adjusting the keel of the upper cutting table
IMAGES A J I P
Information!
1.You will need a slide gauge and a ruler (not included) to
carry out this adjustment.
Checking
1.Remove the locking element 38 of the guard 26 of the
upper table.
2.Tilt guard 26 backwards.
51