stayer SC250W Manual De Instrucciones página 54

Setting for inclined horizontal cutting on the
lower table
IMAGES B R
For carrying out inclined cuts horizontally, the machine
head can turn horizontally up to 90º. To facilitate work, the
lower cutting table is provided with 4 pre-set positions at
+- 22º 30' and at +- 45º that may be selected by means
of conical drill holes in the lower cutting table 6 and the
automatic locking bolt 14.
1.Loosen the two buttons 8 for horizontal locking.
2.Raise and keep raised the anchor bolt 14 for pre set
horizontal lockings.
3.Move the assembly cutting head / lower cutting table 6
to the chosen angle by means of the scale
7 that is graduated in degrees and indicator 9.
4.Tighten buttons 8 for horizontal locking.
5.Release anchor bolt 14.
Setting for vertical inclined cutting on the lower
table
IMAGES A G
For carrying out inclined cuts vertically, there are two
abutment inclinations which are calibrated and pre-set at
0º and 45º. Use a goniometer for adjusting to intermediate
angles.
1.Loosen lever 15 for vertical locking.
2.Select the cutting angle.
3.Tighten the lever 15 for vertical locking.
Setting the cutting stopper on the lower table
IMAGES B S T U
1.Loosen screw 39.
2.Insert profile 41 into insertion cavity 44.
3.Push profile 41 into 40 until abutment.
4.Tighten screw 39.
5.Loosen adjusting wing nut 43.
6.Adjust cutting length by moving stopper 42.
7.Tighten adjusting wing nut 43.
Carrying out the cutting operation on the lower
table
IMAGES A B U
1.Prepare workpiece by fastening it in a completely safe
manner.
2.Start the electrical machine by pushing switch 2.
3.Wait for some seconds until the cutting disk reaches its
maximum speed.
4.Slowly lower the operating head by a continuous manner
and without jerks, using hand grip 4.
5.Exert pressure in the blade's direction of advance with
an intensity being suitable for the material to be cut.
6. Once the cutting operation has been completed, raise
operating head again. Stop the machine by pushing
switch 2.
ENGLISH
54
Use as circular saw by means of the upper cutting
table
Information:
This chapter is applicable to models provided with an upper
table: SC250WPRO, SC265W, SC291W , SLL265W,
SC2500W and SC2600W.
Warning!
Before carrying out any operation on the upper cutting
table it is mandatory to prepare the machine suitably. For
this purpose, the stationary safety guard is to be installed
on the lower table.
Installing the stationary safety guard on the
lower cutting table
IMAGES A B V
1.Begin with the head raised and the cable unplugged.
2.Loosen frontal wing nut 24.
3.Insert the guide of safety guard 34 onto the screw of
wing nut 24.
4.Apply guard 34 at its location according to the figure.
5.Smoothly lower the head and block it by means of
button 31.
6.Push guard 34 downwards ensuring that the guard
abuts against the lower cutting table.
7.Firmly tighten wing nut 24.
8.Check that the blade rotates freely.
9.Finally, briefly start the machine without load and ensure
that the disk does not friction.
10.Disconnect the electrical power jack again.
Setting the upper table
Setting the height of the upper cutting table
IMAGES A B O W
Information:
The height of the upper cutting table can be adjusted from
0 to 42mm.
Warning!
The height of the upper cutting table in respect of the
cutting disk must be such that the disk protrudes from the
workpiece only by a height equal to that of the saw tooth.
See image W.
1.If tightened, slightly loosen the screw of the shaft of the
guard of table 25 such that the guard ascends freely.
2.If tightened, loosen lock 38 of the guard of table 25 such
that the guard ascends freely.
3.Loosen the wing nuts 24 that regulate the height of the
upper table.
4.Adjust the height of the table by smoothly pulling it
upwards.
5.Firmly tighten the wing nuts 24.
54