Special Safety Precautions - stayer SC250W Manual De Instrucciones

Setting the cutting width on the upper table by
means of the guide
IMAGES B P
1.Release movement of the parallel guide 27 by loosening
wing nut 28.
2.Adjust the cutting width by moving the guide 27 on the
graduated scale 45.
3.Fasten guide 27 by firmly tightening the wing nut 28.
Using the goniometer
Information!
IMAGES P Q
The upper working table is set for the optional use of a
goniometer that is adjustable between 0º and 45º.
The regular use of the goniometer is for cutting slanted
cuts, but there is the possibility to use the goniometer
as a depth control stop for adjustable cutting. Mount the
goniometer at the right side of the upper cutting table for
this purpose.
There is a model-specific goniometer for upper aluminum
tables (SC250W, SC265W, SC291W, SC2500W and
SLL265W) and another for upper steel-plate tables
(SC250WPRO).
1.Loosen the lower wing nut for coupling to the upper
cutting table.
2.Insert the goniometer into the front slot of the upper
cutting table.
3.Adjust the position of the goniometer in accordance with
the work to be carried out.
4.Tighten the wing nut for coupling the goniometer to the
upper cutting table.
5.Loosen the upper wing nut for adjusting the angle of the
goniometer.
6.Adjust the angle of the goniometer in accordance with
the work to be carried out.
7.Tighten the upper wing nut for adjusting the angle of the
goniometer.
8.Loosen the upper stop-extension wing nuts of the
goniometer.
9.Adjust the extension of the stop of the goniometer in
accordance with the work to be carried out.
10.Tighten the upper stop-extension wing nuts of the
goniometer.
Carrying out the working operation on the upper
cutting table
1.Carry out the starting operation with locking as explained
in 12.
2.For longitudinal cuts use the parallel guide to support
the workpiece.
3.Approach the workpiece to the cutting disk applying
maximum caution keeping your hands distanced from
the cutting path.
4.Push the workpiece with an intensity that is suitable for
the characteristics of the material.
5.Carry out the stopping operation with locking as
explained in 12.
ENGLISH
55
Information!
Only for models SC250W, SC265W, SC291W, SC2500W,
SC2600W and SLL265W. Once it has been placed at the
left of the saw blade, parallel guide 27 allows to cut small
cuttings at 45º.
13. Precautions and protective garment
This electrical tool may only be handled by adult personnel
who have received suitable training and instructions,
complying with laws as established to this respect and
what has been set forth as a matter of prevention for the
working place.
In addition, the operator must have understood and
assimilated, and fully comply with the present manual.
This machine requires the use of the following individual
protective equipments:
1.Protective helmet
2.Integral face-protecting equipment (eyes and face)
against impacts
3.Ear protectors
4.Dust mask
5.Protective gloves against mechanical aggression
6.Boots with toe caps and insoles
7.Working garment
8.Tool bag
9.Safety belt (occasional)

14. Special safety precautions

Safety Precautions
- Do not use saw blades that are damaged or deformed.
- Do not use the saw without guards in position, especially
after a mode change, and keep guards in good working
properly maintained.
- Replace the block of the table when worn.
-Only use blades recommended by the manufacturer
saw, with a warning that the keel should not be thicker
than the width of the groove of the cut made by the
saw blade and not thinner than the body of the blade;
Specific saw blades for cutting wood must comply with
EN 847-1.
- Do not use saw blades made of high speed steel.
-Dressing appropriate personal protective equipment
when necessary, which may include:
• Hearing protection to reduce the risk of induced hearing
loss.
• Eye protection.
• Respiratory protection to reduce the risk of inhalation of
harmful dust.
• Wear gloves when handling saw blades and rough
materials (leaves should be on a stand whenever
practicable).
- Connect the saw to a dust collection system when
sawing wood.
- Always store the push stick in place when not in use
Description of risks specifically related to the
machine
Any of the following prior risk conditions must have existed
for the risks to become real:
55